L3200 hydraulic relief valve question

dbach81

New member

Equipment
L3200 HST
Aug 5, 2015
4
0
0
Wichita Falls Tx
Greetings, I'm new to the forum so excuse me if there is already a thread on this but I have the LA524 loader and was looking to bump up the pressure on my hydraulic relief valve. I ordered the washers that kubota uses to put under the relief valve spring. I put a .2mm washer in and put a pressure guage quick coupled on the loader valve. My pressure reading is 1650psi. My question is does the loader valve have a relief valve in it also? And is that the best place to check pressure? I've heard people say never dead head the flow and others that say that's a good way to check pressure. Thanks for any help.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,786
11,492
113
Sandpoint, ID
What was the pressure reading when you started?
 

dbach81

New member

Equipment
L3200 HST
Aug 5, 2015
4
0
0
Wichita Falls Tx
Sorry forgot to mention the pressure was unchanged at the loader valve after adding .2mm washer. Are there any relief valves in the loader block? And is that pressure low? My loader is working but the reason for wanting to add some pressure was the loader has seemed weak and not breaking out of dirt piles as well as it use to. I have to reverse the tractor shake some dirt out of the bucket and then it will go on up. I went back to the dealer and the mechanic there said there are relief valves in the loader block as well and if I wanted to check system pressure to put the guage on a port down under the seat. But I'm not sure. Thanks.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,786
11,492
113
Sandpoint, ID
The loader valve does not have a separate pressure relief.
And no do not dead head the system it will blow seals.
If you installed the shims and got no change in pressure, you have either installed the shims wrong or your pump is having an issue and can not build pressure (rare).
You should be seeing pressures in the 2275-2417 range to the loader.
 

dbach81

New member

Equipment
L3200 HST
Aug 5, 2015
4
0
0
Wichita Falls Tx
Ok, so I need to T into the system somewhere then? Had the guage on it again today on the loader up function. It read 1700 psi. I'll go get some parts this weekend so I won't be deadheading the system. I have a blown up diagram for the relief valve and everything looks to be correct. I have a .4mm and .1mm washer also any idea how much pressure the washers add by thickness?
 

yamatitan

Member

Equipment
L3901
Jun 28, 2015
38
1
8
Louisiana
Dont know if you did it yet but I just did mine today. Got 41.6667psi per .1mm according to my gauge. My front end loader is a beast now was regretting not going with a bigger tractor but needed the smaller size to fit in the woods, no regrets now. My loader was 250psi below spec from the dealership I put it 250 psi over spec hopefully I dont break anything. That comes out to 10% over spec figured it would be safe as long as I keep enough weight on the 3pt. Most of the time I was fine with it how it was before but there was a couple times it couldnt lift something I needed now it can.

By they way im new to all this and just put the gauge into the quick coupler off the loader valve. I dont believe your deadheading the system by doing this it should still flow back to the 3pt next how I understand it.
 
Last edited: