FEL is not level

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,778
11,486
113
Sandpoint, ID
The OP wanted to know if there was a simple adjustment
The first statement is weird / creepy as you are the OP.

The video you posted is NOT to level the loader, the video shows a way to fix clocking of the SSQA plates.
This is NOT you're issue and if you do it you will mess up your SSQA.
The only way to fix an unlevel loader, that is not bent, is to lossen the loader mounts and level it from there.
 
  • Like
Reactions: 1 users

Beebad

Member

Equipment
Kubota L-3560 HTC
Oct 12, 2024
88
17
8
Northern New Hampshire
The first statement is weird / creepy as you are the OP.

The video you posted is NOT to level the loader, the video shows a way to fix clocking of the SSQA plates.
This is NOT you're issue and if you do it you will mess up your SSQA.
The only way to fix an unlevel loader, that is not bent, is to lossen the loader mounts and level it from there.
Thanks, the original post asked whether there was a simple adjustment to level loader. Loosen loader mounts, good. I just wanted to know if there was some method…i still don’t really know what or if i have an issue with the FEL and I certainly won’t do anything, if at all, without exhaustive research…. I really appreciate the help.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,778
11,486
113
Sandpoint, ID
OP is not Original Post it's Original Poster, reread what you wrote and you'll see why it's a weird statement. 😜

Put a level on the back of the towers, that's the quickest way to tell if there is an issue.
They should lean forwards or backwards the same amount.
 

Grandad4

Active member

Equipment
1949 Farmall M, previously owned: L 4610, BX 2230
Apr 5, 2016
453
199
43
Greensboro, NC
A simple way to adjust a minor difference like you have is to add or release a little air from one of the rear tires. It shouldn't take much to close a small gap like that. Neither you nor the tractor will notice that one rear tire has a couple pounds less air than the other.
 
  • Like
Reactions: 1 user

Red Dog Tractors

New member

Equipment
Kubota L Series
Nov 11, 2026
2
0
1
Austin, Texas
I noticed that the one side of the loader is slightly higher than the other.

Can this be adjusted? I noticed it more with the forks attached.
thanks
Good suggestions already. Swapping the tractor around on the same spot is the quickest way to rule out the floor. If it’s still high on the same side, check front tire pressures and compare both lift cylinders for a slow bypass. Raise the loader a foot, let it sit 20 minutes and see if one side drifts. Also measure the forks themselves from the frame to the tine tips, because a bent or uneven fork frame shows up more than you’d think. A cheap digital angle gauge laid on the quick-attach plate makes it easy to see exactly how far out you are.
 

Beebad

Member

Equipment
Kubota L-3560 HTC
Oct 12, 2024
88
17
8
Northern New Hampshire
Good suggestions already. Swapping the tractor around on the same spot is the quickest way to rule out the floor. If it’s still high on the same side, check front tire pressures and compare both lift cylinders for a slow bypass. Raise the loader a foot, let it sit 20 minutes and see if one side drifts. Also measure the forks themselves from the frame to the tine tips, because a bent or uneven fork frame shows up more than you’d think. A cheap digital angle gauge laid on the quick-attach plate makes it easy to see exactly how far out you are.
Big headache today, i removed the FEL to practice in prep for attaching the L-4455 subframe as soon as the Kubota drawbar arrives tuesday… went like clock work until it was time to reinstall the FEL. THE RIGHT SIDE was a 1/2” higher than the other side and the Pin Would not go in. The left side no problem. I got a 4-ton floor jack and a block of wood and lifted the corner near the corner of under the cab until the damn thing settled into place.
 

whitetiger

Moderator
Staff member

Equipment
Kubota tech..BX2370, RCK60, B7100HST, RTV900 w plow, Ford 1100 FWA
Nov 20, 2011
3,840
2,232
113
Kansas City, KS
check front tire pressures
One more time, the air pressure in the front tires cannot affect the loader being higher on one side than the other. It is physically impossible.


compare both lift cylinders for a slow bypass.
It is physically impossible for an internally leaking cylinder to allow one side of the loader to settle.
Also, the shafts can not enter cylinders that are already full of oil. It's physically impossible.


A cheap digital angle gauge laid on the quick-attach plate makes it easy to see exactly how far out you are.
One could also read tea leaves.
 
  • Haha
Reactions: 1 user

whitetiger

Moderator
Staff member

Equipment
Kubota tech..BX2370, RCK60, B7100HST, RTV900 w plow, Ford 1100 FWA
Nov 20, 2011
3,840
2,232
113
Kansas City, KS
I got a 4-ton floor jack and a block of wood and lifted the corner near the corner of under the cab until the damn thing settled into place.
Could you elaborate on this comment? It paints a very abstract picture.
 
  • Like
Reactions: 1 user

airbiscuit

Well-known member

Equipment
New Holland T2310, New Holland TC21D, Kubota l3010 GST, Farmall H
Mar 18, 2021
461
554
93
NW WI
Are both hydraulic rams extended exactly the same amount?
 

whitetiger

Moderator
Staff member

Equipment
Kubota tech..BX2370, RCK60, B7100HST, RTV900 w plow, Ford 1100 FWA
Nov 20, 2011
3,840
2,232
113
Kansas City, KS
Are both hydraulic rams extended exactly the same amount?
There is a torque tube between the two boom arms that keeps them equal.
You can remove one cylinder, plug the hose ends, and raise the loader using only one cylinder. The loader will still raise level.

Disclaimer:
I would not try that with a load in the bucket.
 

nbryan

Well-known member

Equipment
B2650 BH77 LA534 54" ssqa Forks B2782B BB1560 Woods M5-4 MaxxHaul 50039
Jan 3, 2019
1,441
951
113
Hadashville, Manitoba, Canada
Confirm the floor is nice and flat. The rear tire and the loader frame contact points must be in the same plane.

Then curl that ssqa bucket frame all the way back so it's the loader arms not the ssqa frame resting on the floor. An out of sync pair of cylinders can throw off the accuracy here.

It's not my tractor so not recommending this, but trying to stress that right arm upwards a bit using that 4x4 block under it, but no block under left arm, then raise front of tractor with the boom hydraulics with just the right arm in contact with ground on the 4x4 block.
Then lower it without the block and see if it's leveled at all.
 
Last edited by a moderator:

Beebad

Member

Equipment
Kubota L-3560 HTC
Oct 12, 2024
88
17
8
Northern New Hampshire
Could you elaborate on this comment? It paints a very abstract picture.
When reattaching the FEL, The pin on the right side would not go in, the hole would not line up; the FEL was about 1/2” high. I jacked up the tractor gently until everything settled in, popped in the pin.. either i was not lined up or FEL isnt level.
 

Attachments

Last edited: