Search results

thanks for your help, i got the snap ring out by drilling a small hole through the cylinder end , and i got the end gland out ,now how do you remove the end cap ?

part needed k2063-16500 steering cylinder,seal kit is only a temporary fix,steering cylinders are defective eating the seals after 300 hours of use

i can not believe they made this steering cylinder held together with a snap ring with no holes to remove it from either end. this should be recalled you loose steering all of a sudden unsafe someone is going to get hurt and sue kubota. You can not even buy the updated part you must wait 1 year...

I have to reseal my steering cylinder, because i can not buy a new cylinder, i have the cylinder off, how do you disassemble it ? I see no end caps?thanks for any help you can give

Bx2200d mows fine for 10 min then dies? Help, i have replaced the fuel supply pump and fuel filters, also tested fuel cap vent by removing fuel cap when it has no power?

My bx 2200d does the same thing i have replaced the fuel supply pump and the fuel filters ? I am stumped how can it run fine for 15 min then no power???

Can i run r1 tires on front and turf on rear of a bx tractor? It had turf tires all the way around ,thought i would buy r1 ag tread on new wheels for the front for snow. And leave the turf on rear, but the new ag tires are total height of 18" and the turf tires i took off are a total height of...

i believe you turn the key backwards hold there for 1 min below 20 f and 30 sec below 40 f. there should be a glowing heating element on dash to show you the system is working.when key is turned backwards

thanks for all you help. i adjusted the stops and the screws on that rod, that helped, then i seen a bracket under the right rear tire. that is near the 3ph valve .it has a big slide on it that you can loosen the bolts and turn it . i moved it a head about 7mm and readjusted screws on the rod...

I have a rear blade on my bx2200d when tractor is cold and you pull the 3 point hitch control to lift the blade you must hold on to it all the time in the up position, if you let go the blade goes right back down on its own. Once the tractor is warmed up the blade will drop sometime when the...

My bx 2200 air cleaner mount keeps busting, i replaced it with updated one from dealer ($100.00)125 hrs ago of run time. And it is broken again were the brackets attach to the engine. Antone with a fix for this?

wow thanks i had never heard of rubber tire chains.

has anyone installed front ag tires for better winter traction if so how did it work. i have 4 turf tires and a concrete drive way, i dont want to mark up with chains so i thought putting on 2 front turf tires in winter would improve traction

The blade is made for the tractor it is a 5' sub compact blade it is a positioning control the rod has 2 springs on it.

Has anyone put ag tires on the front and turf on rear? I do a lot of getting stuck in wet snow off the pavement.

what makes hydraulic control lever return to center. my bx2200 hydraulic control lever wheel not return to center after pulling it up the whole way in lift mode after you let go of the lever it returns to the down position instead of center and the blade drops. I must hold up on the lever in the...

I have a bx 2200 with a front loader . The rear blade drops by its self. Seams worse when i drop the front loader on float. How do i keep this from happening?

fixed starter by cleaning starter solenoid contacts

Can you replace starter contacts on a bx2200, my starter just clicks when i hit the key.

Took my loader off, now rear hitch wont go up. There are 3 lines quick disconnect that come out of tractor and go to loader.do i need to jump 2 of these lines? Can i damage tractor if i jump the wrong 2? I did plug one from tractor into other one from tractor hitch still does not work .help i...