Search results

Update....' I received the kubota plug from Speed25 and finally finished installing it between rains. Worked perfect! Thanks Speed25. The plug Speed25 sent me was from Valley Enterprises but if there were any numbers to identify the part they are long gone. I visited their site but could not...

TheOldHokie.... Wow. Both lungs! I can't imagine going thru that. Sounds like you have been greatly blessed! I hope your recovery is going very well and can enjoy life again. I'm hesitant to bother you with a project that I may or may not attempt. I'm sure I'll do it at some stage but...

I think I posted the wrong link for what I had in mind. His kit was for a L4701 instead of a L2501. He was able to do everything with the port under the seat. Have a look and see what you think. The L4701 port may be different than the L2501. Anyone know if it's different and can you see any...

This will most likely be a diy job. Mentioned Kubota dealer just to see how they would go about it. Question... what is the difference in the port under the seat vs the port under the right floor board? Can either be used for what I'm attempting? Reason I was thinking the port under the...

Received the Opti-lite. Looks very sturdy... all metal except for the handle, and rubber boot over the on/off switch. I think I figured out where/how to mount it. Waiting for a connector from Speed25 to complete the install. Thanks for the help guys.

Thanks guys. It looks doable (famous last words). Looks like the port is under the seat which means short hoses. Don't know if I'll need to buy a different lever cover for the control lever. I might stop by my local dealer and see what they offer and recommend vs what I really need. My...

This is probably complicated and expensive but I have thoughts of sometime in future needing rear hydraulics on my newer L2501f which came w/o loader. I have access to a tractor with FEL and only needed to mow about 10 somewhat wooded acres and FEL is awkward in this situation. Being that it...

Now there's a thought! Thanks!

Thanks Speed25. Yes, I would like to get the male plug for the L2501. I clicked on your user name and did not see how to "PM" a member. I did see a "start conversation", maybe that's it? It looked suspiciously like I might be posting on the forum rather than a PM and didn't want to give the...

Thanks Speed25. I may have found them. I searched for "2-Pin Power T-Male/Female Connector". They look the same on Amazon. Others sell them also. I just didn't know what to call it and came upon a post here that identified it. If you know yours fits the Kubota plug a part number would be nice...

I received the leds but there was not enough room to fit an on/off switch into the housing. I returned them and purchased an opti-light rear work light with a built in switch. Haven't received it yet but will update and report on how it works. Thanks for the suggestions....

On my 2023 L2501f there is the extra unused female plug evidently for a rear work light. I can't find it in my manual as to what type receptical it is but looks like it's made for spade type male plug and the spades are at intersecting right angles to each other.... kind of like the letter "T"...

That looks interesting Dustball. My lights are on the way and will see if I can add a on/off switch. If not this may be the way to go. Tks...

I'm an old fashion guy that likes simple. Instead of running wires around to the battery and mounting switches and such in my way I have choosen to wire to the hot wire under the left fender with the switch built in to the light proper. Only ones I've come across with the integral switch are...

Looking at Amazons Nilight 18W flood light for a rear work light on L2501. I'd like to install an internal on/off switch to the pod and wire to the left tail light directly w/o external/additional wiring for a remote switch. I'm sure I can source a weather proof switch, I just don't know if...

You are right about the specs on the "F" model... 2wd, 8 forwards and 4 reverse, ag tires... a plain old B flat tractor :) I could possibly make the L4060 guard work but it's about 5-6 hour drive just to look at it and decide then compare that with what's on a L2501/2 at my local Kubota dealer...

New here. Purchased a new L2501f and it came without the brush guard. I've found a new old stock for a L4060 and wondered if it would fit my L2501f. I can't seem to find if it's the same part number. Tractor came w/o FEL as I didn't need it (have a L2800 w/FEL). Using the L2501f for finish...