Search results

Most Tractors i have Seen with Rear Mounted SnowBlowers Do The "Lift Before They Finish The Run Deal"

I have a few parts to get rid of, and thought someone may want them. Fits a 1989 Kubota B8200 4x4 I have 2 New Kubota PTO Drive shafts (About 10" long) 1 New Kubota Complete Fuel Filter Bowl Assembly 3 New Kubota Fuel Filters 2 Blue Axle Supports (not sure where there go?) If your...

YES... Excuse my Brain Freeze ,,, LOL For some Reason i thought you had no access to any other places to change the oil....

Yes... They take about 20 seconds to show up ..... After 30 seconds it does not get much brighter, but for winter strts keep holing it there for a bit longer....

I AM NOTICING A FEW ELECTRICIANS AND ELECTRICAL RELATED PEOPLE HERE TOO... Hmmm ..... from Electrical to Tractors, must be a CONNECTION some place. Bubba

Tae Kwon Do .... OK ... REALLY NO ONE INSULT HAPPY JOE .... HE WILL SLAP US SILLY!!! Thats Cool Joe ....

How would you Refill it? there may be more oil needed? Have you tried a Flexible thin wall socket, and ratchet with fine clicks for tight spaces? Not Sure just my 5 cents Bubba

Lol... Any suggestions where to get real shear pins then? And how much they are? I measured and i need 2 1/2" x 5/16 thanks bubba

OK .... I will give it a try. I will Check my Loacl Home Hardware Store and see what they have.

Gee.. and i thought the "Cannary" Died from the Cold in my Garage, cost $12. to replace those buggers... LOL PITA Forgive the Joke....

Is There a Standard Size Shear Pin to Fit the PTO Shafts on a Front Mounted Kubota Blower? Is there Aftermarket Ones Cheap?? They Appear to be about 3" long and 5/16" thick Let me know Please. Bubba

Well ..... That May Melt on you, be careful... I've Seen my Dryer Almost Melt that Stuff when it got Plugged up... That Foil Pipe can only take so much heat, not sure what Fumes will do to it, or the Plastic Vent. Must be Flexible Exhaust Tubing Available some place near you, its usually sold...

Well .... My Garage is NOT Heated ... so i just crack the Doors Open, and Let It Idle a few minutes (about 10) .... Then Move it Out... Pulling it Outside sooner will make the Garage Less Full of Fumes Thats for Sure. I Can't Say I would do the Same if my Garage was Heated though, cuz I'd be...

"ARCY" you may be right ..... my Best Time was 220 volts Grounding to my Aluminum Ladder(The Good Ole Days Before FiberGlass..LOL) 30 years ago,,, it Arced through my T- Shirt and was Bouncing all over my Chest Hair.... What a Light Show !! What a Different Tingle i Must Say ..... That was...

I Managed to Buy one for $29.99 Canadian .... NON KUBOTA Part.. Kubota Wanted $187. for a Top Link I Am Presuming ts just a Standard Farm Tractor Cat 1 Top Link Got it at NorhShore Tractor in Echo Bay, Ontario , very Helpful and they do not just push there Kubota OEM Parts. OB1 ... Welding...

If you take it easy it should work fine... I have a Shitty SnowBear Snow Plow and its made Cheaper than that, still works fine after 8 years. I never Ram anything with it, going nice and Slow gets the job done. I would make sure the springs on the Snow Blade are not too tight so it Breaks away...

found it by fram .... Thanks fram oil filter number #ph3593a fram air filter number #cak530 fram fuel filter number #c6921 for a kubota b8200

Thanks that gave me the FRAM OIL FILTER NUMBER #PH3593A Any Help with a Good After Market Air Filter Number now? Thanks

1989 4X4 B8200 FRAM OIL FILTER NUMBER ? Anyone have the Filter Number, or another name brand oil filter number that fits my B8200 Also, if you have a FRAM or after market Air Filter number and make i will take that too. Thanks - Bubba aas@nt.net

Need a 1898 b8200 4x4 rear rim to fit 12:4x16 turf tire its held on by 6 fasteners (4 bolts & 2 nuts) the bolts sit 6" apart when measuring across the axle hole to the next lug. The center axle is about a 4-1/4" hole. If anyone has a good 2nd hand one to sell, or even give away let me know...