Search results

I have a BX 2763A front snow blade on my BX1870-1. Does anyone know of a company that builds specific side extension wings for this blade. Have already contacted bxpanded and some others who deal in aftermarket Kubota attachments. Like to find wings specifically made for this blade before I...

Used 8" or 12" wide bucket for a BT603 BH on a BX23s.

Wanted to buy, used 8" or 12" wide bucket for a bx23s/bt603 BH.

Have a MX5100dt w/ FEL. Would removing from tires make it easier to access drain plug and fluid? Would support front with FEL. Realize it is not necessary however would make must less mess on draining fluid. Suggestions. Owners manual has fluid capacity at 11 1/2 qts., Dealer says 9 1/2...

Looking to buy a used snow pusher to attach to a BX23s FEL QA, 48" to 60" width. Northeast Pennsylvania.

Want to do some arc welding on my BX23s loader to install hooks. Should I disconnect the battery? Any other issues I should be concerned about?

When working on/doing service its is easiest to access the engine area with the FEL arm elevated. Yes, you could remove the FEL or place a support post under the arm/s. I have heard tell that some use angle iron piece attached to the lift cylinder rod whereby NOT allowing the lift cylinder...

When securing a BX TLB to a trailer should the BH boom and dipper stick be lowered to the deck OR left secured in its normal non-use location, pinned? Does it matter? Any ideas?

I own a bx23s. I had purchased several items from bxpanded including their BH ripper. While digging out a stump I bent the ripper. Have others experienced this? I have contacted bxpanded and waiting for their reply.

Adding a 3-pt ballast box to the rear of my BX1870 for additional weight for plowing snow. And "yes" it is coming. Inside box is approx. 5 CF. A cubic foot of concrete weights 150#, without splitting hairs. This means concrete would weight 750#, plus box of approx. 100#. 850# total...

WTB, new OR used 8" OR 12" backhoe bucket. Used on BX 23s, located in NEPA. Call or text 570, four four one, five six two one. Purchased with the 16" bucket and looking for something a little narrower. Will pay cash. send pictures and asking price.

My bx23s with approx. 110 hrs on it, on occasion when using the hoe, I can hear what seems to be a growling type noise, not real loud and only last a short time. NO affect on the operation. Don't hear it when using just the FEL. HST fluid level OK. Have made my dealer aware of this. Has...

Has anyone tried running a 5' rear finish mower with a BX1870? I once had a B1550DT and tried to run a Woods 5' finish rear mower and would not do it if heavier grass. The BX 1870 has a little more PT0 Hp, but not sure if enough to make a difference with the BX being a hydro and the B1550 was...

Have issues with both my BX1870's. MMM linkage will NOT lower down far enough to hookup MMM. Height adjustment dial is set on "0". Rear 3-pt valve works find and but don't think this regulates the MMM linkage, just the 3-pt lowering. Have to lift up MMM some to hookup. In years past never...

Have a MX5100DT. In the process of changing the fuel filter, I rotated the petcock to the "off" position as as the arrow indicated and as I have done in the pass. Upon removing the large nut and bowl, some fuel continued to run. I immediately checked position of the petcock to make sure it...

Issue with the 3-pt needle valve control which regulates the speed in which the 3-pt lowers. Was not allowing 3-pt to lower with ballast attached. Had to turn the control nearly all the way out to get 3-pt to go down. I do turn this control knob in/out occasionally to make sure it does not...

Does anyone have any experience purchasing and/or using a "Johnny plow" brand hyd. dozer/snow blade pros and cons for Kubota BX's. They seem to mount nearly the same as the Kubota front blade model but sell for a little less. Tks.

Has anyone run into issues with their valve stems with rim guard ( beet juice). Valve stem cores coming out when stem cap is taken off.