Search results

I ordered from him a few years ago, It took a couple of emails for him to respond but once he did he was very helpful. I ended up ordering the CUT24 model but I wanted to make sure I could really raise them up so he made them taller for me. they are really heavy duty skids probably overkill...

Congrats!!! I was going to say how useful those forks will be, but from the picture I think you already know that. :D

Nice find !!!, I missed these when I was looking. Looks like they have a nice high back stop also. If you end up getting them report back on how you like them, may help someone else. Sent from my iPhone using Tapatalk

"DJI designed the Mavic Mini to weigh 249 grams, putting it just below the Federal Aviation Administration's 250-gram weight limit that requires a drone to be registered." This applies for recreational purposes but if used for commercial purpose requirements may be different. I just have a DJI...

SSQA Pallet forks from BXattachments.com weigh 180 lbs Landpride PFL1242 weigh 220 lbs Worksaver ssqa pallet forks weigh 220 lbs Artillian Frame and Forks - weigh about 215 lbs The Artillian frame allows you to later add a grapple using same frame Think you'll find the PFL1242 or...

Are you saying you can't lift them at all or just not full height? If you can't lift them at all maybe you should check the hydraulic pressure, might have to boost it up a little. Ive lifted my 450 lb grader scraper to about 4 feet high with my BX2670 and my pallet forks weigh 162lbs and quick...

I don't have SSQA, so went with Ai2's forks and quick attach system. they work great. I've only had them about a year but already my favorite attachment and the carriage and forks only weigh 160 lbs combined so I don't lose much lift capacity. The SSQA version carriage weighs about 20 lbs...

Almost forgot, also had to replace one fitting that is on the tractor as it was 3” long and replace with a standard size fitting so the kit would fit, so you may want to see what your tractor is using, I think the fitting was a 37 degree flare to straight thread 9/16 - 18. Before and after...

I installed this kit last year on my bx2670-1, The install is not really that hard but there is not much room to work, Everything has to line up perfectly. I also suggest crows foot wrenches and stubby open end wrenches to be able to tighten everything down. I think I mainly used 18 and 19mm.

I have Ai2 QA system (which is basically comparable to Kubota QA) and I have never used SSQA, but watching videos of people with them, i believe the QA probably takes a little more finesse, It usually takes me 2 - 3 attempts to make the connection. The QA weighs 50 lbs, and Ai2 Carriage and...

This is only my 3rd year with the tractor so I***8217;d guess the blower has no more than 50-60 hours on it. The left auger bearings locking collar basically split, the other side and impeller bearing were fine but I replaced them anyway as I ended up taking it all apart. Sent from my...

Think you nailed it NIW, the new bearing didn’t want to go back on either so per your direction ran a file around a bit and it did seem to help but still needed a little persuasion. Probably wouldn’t have been too bad if that shaft would have slid out of the bearing as it was supposed to...

Well I had to remove the bearing from shaft with a crowbar but it’s off anyway, might as well replace all the bearings seeing I’ve gone this far. Hopefully it goes back together easier than it came off. Sent from my iPhone using Tapatalk

Thanks, I thought it should slide through the bearing, but it’s not doing it, the fan slides along fine but it appears the bearing is not allowing the shaft to slide through at the very end of it, spraying it all with pb blaster now to see if it will loosen up. Sent from my iPhone using Tapatalk

Ok got this far but can’t seem to get the shaft all the way out, do I need to remove the plate in the 2nd pic holding what I believe is the impeller shaft bearings? Sent from my iPhone using Tapatalk

Does anybody have an easy way to change the bearings, the left side needs to be changed and only way I see is to remove the entire auger and fan assembly, just thinking there has to be an easier way. Sent from my iPhone using Tapatalk

I have a 2670 with QH-05 and RB1560 - with a short top link the blade is around 19" off the ground, with long top link not sure but would guess maybe 6". I only use it for snow removal so probably would have been fine with rb0560. I did install rear remotes with top link so i could adjust...

If you're using standard 12v relay I believe the constant hot from back of tractor should go to your switch then from your switch to terminal 86 on relay, and ground terminal 85. Then u need a constant hot to terminal 87 on relay, then wire from terminal 30 of relay to your lights. when you...

I’ve got his gen2 series for my 70 series with his QA and they are great, allows me to stack my implements to make more room in my garage. Sent from my iPhone using Tapatalk