Recent content by Daniel Pullum

  1. D

    There is alot about this site I don't understand. I have not been very regular about signing in...

    There is alot about this site I don't understand. I have not been very regular about signing in. I have gotten some good info. Just posted a note about my "growling" right rear B3200.
  2. D

    RCK 60 BA gearbox oil seal

    Thanks for the comments. Sorry I'm not very regular about checking for comments. I was able to change the oil seal as suggested. The repetition was caused by the snap ring on the main shaft inside the gearbox was missing. Certified dealer missed it also..... I found another cure: I bought...
  3. D

    Growling B3200 right rear wheel.

    I'm short on specifics as I just noticed it this week. Pulling on a small stump caused some wheel slip. I heard a "growing" noise in the right rear. Full service recently, 1380 hrs 2012 tractor. I plan to jack up on stands and run. Appreciate any other suggestions.
  4. D

    Kubota radiators!!!

    Excuse me. I thought someone might have a suggestion for cleaning the radiator and I got that. Thanks to those two postings.
  5. D

    Kubota's in General

    Is there a B3200 "club"? I bought this new in 2012 and it is my fifth Kubota---- B1400?, B7850, B2400, B2710, and B3200. I've loved every one of them until I got the next one and loved it more..... I lost the wiring harness on the B3200 (shorted out) at 600 hrs; broke a lift arm bracket at...
  6. D

    Kubota radiators!!!

    Hello, I'm sure some of you have experienced cooling problems related to Kubota radiators. I do some bush hogging every year and mow about 4 acres of yards. Well after 9 years the tractor began overheating after 30+ min. I lost the pre-screener some time ago which may or may not have...
  7. D

    B3200 mower deck & joystick control valve

    Hello I have a 60" mower deck for a B3200 RCK 60BA? It is in good condition except for the bottom oil seal on the main deck shaft. I have a new seal. I moved up to a 72" deck. I removed the original joystick control valve and changed the feed line to a four spool valve body to operate a 4n1...
  8. D

    Hour meter has stopped.

    A B3200 is a slightly larger/older version of Ur 2501. Mine weighs 1700+/-100 and has the 4 cyl engine. It was new in 2012 and now has 1275 hrs. But I discovered yesterday the hour meter ain't runnin. The tach is but I believe that is electrical.. I'm going to check the "drive...
  9. D

    Hour meter has stopped.

  10. D

    Bevel gear housing leaking. B2650hst 4wd cab

    My B3200 spindle seal leaked at 909 hrs. I pulled it apart replaced the seal (real challenge getting the old metal part off and new one in place. I must have pinched/twisted/mangled something because it began leaking again after 90 or 100 hrs. I ordered a new seal and was trying to build-up my...
  11. D

    I had a B2400. It had 85 hrs when I bought it from the dealer. At 600 hrs the hydro peddle went...

    I had a B2400. It had 85 hrs when I bought it from the dealer. At 600 hrs the hydro peddle went nuts. The tractor would run/move until I dropped the scraper and the peddle hammered like a machine gun. The dealer checked out, with no solution and called Kubota Central Service Center. A rep went...
  12. D

    RCK60-32 manual needed

    I had three rck60's and may have a copy left. I also have a rck60 that came off of my B3200. Need parts or the whole thing????
  13. D

    Hour meter has stopped.

    I considered that but did not investigate, but I will. Another OT made the same obserrvation. Thanks
  14. D

    Hour meter has stopped.

    Help. My hour meter (on my B3200 purchased new in 2012) has stopped. I've no idea when. Absent minded to say the least. Can it be repaired, replaced or by an independent timer.... Thanks in advance
  15. D

    What's new with you Good Sir? The ballast box is great. I've used it for a tool carrier more...

    What's new with you Good Sir? The ballast box is great. I've used it for a tool carrier more than a counterbalance so far. I've been cleaning up some of the junk from my parking area. I had a 5' belly mower that I had stripped of parts. I have another 5' belly mower that is complete but needs...
See more
Top Bottom