Recent content by coreyperez

All, I haven't done much other than reattach the grapple and things were moving for the couple minutes I drove the tractor. I do still have the steel tube and will likely figure out all the mess I got myself into when this was installed in 2015. That said, I let a friend from the Military...

I will still need to get out and reconnect the grapple, but when I started the tractor in the morning to move it, (yesterday) it still had the issue, but in the evening, the issue was improved. I didn't change anything aside from where it was parked. Here is the picture of the two valves I...

Dan, I will see if I can try and find the instructions I received for the 3rd point (electric solenoid). The blue lines, one goes to the port under the seat and the other connects to that block under the floor. I did some digging and found the email/attachment I received from Landpride to...

All, Thanks for your interest. 2015(ish) L2501 with 394.2hours. The tractor has been equipped like this since new. Approx 150hrs on the hydraulic filters/fluid (last changed at 252hours). I have never altered the hydraulic pressure and only used Kubota UDT Fluid. 3-point appears to work as...

Thunder Chicken: I just threw up in my mouth a little... Holy crap... So, I got my L2501 back. They (mechanics) worked with Kubota to diagnosis the problem. In the end the dealership decided that they don't think there was a problem. The instruction was to pull filters in 50 hours and see...

Just a quick follow up. The Mechanic called today and we discussed a few things. He is troubleshooting per Kubota's instructions. The local dealership has gone through a few software changes and they didn't have my service history. Luckily I had kept the 50hr service receipt. They were able to...

I just got a call from the Kubota dealer. They want me to bring it in and have the mechanics look it over. I figure for the 2 hours labor it is worth the piece of mind. I've noticed this year that they HST whines a lot more than it did previous years, the HST treadle is very resistive when...

I have a tendency to run mine colder than that, depending on weather events. I have constantly ran mine at -30f (-35ish C). None the less, awaiting to hear back from Kubota on the issue. Corey

Thanks for the replies and suggestions. I too feel that the chips and swirls look like manufacturing debris. I REALLY feel like they should have gotten that amount cleaned up during assembly, or else they need to improve their processes. As far as adding magnets, I use filtermags (external...

Results of the (external) filtermag

Hey all, I just hit 250 hours and was doing my Hydro service. When I pulled my (I think return filter, right side, underneath foot rest) I found what I would consider a large amount of metal shavings (looks like manufacturing due to spirals). I figured this was due to being the initial filter...

Re: L2501 "Power Beyond Port" connection for Land Pride 3rd Hyd point / Grapple Gentlemen, Sorry for the delay. I didn't seem to get notification about your questions and only stumbled upon this thread while looking at some unrelated questions. I got the Land Pride grapple from the Kubota...

Wow Greg, Thanks for the detailed response. I called the local glass company. They one do laminated safety glass, (no curve) but do regularly do boats and other heavy equipment. Hopefully the cost well be closer (or cheaper!) They quoted 15$ - 17$ a SQFT. I just purchased a Miller...

Greg, I didn't see a parts list (hinges, latches, wipers, etc). I live in Alaska and stumbled upon your build researching a cab build for my L2501. I know you got your glass done locally, and it sounds like it was relatively inexpensive. I had been looking at commercial available items, but...

Just to close out my question about the 3rd point, below is the URL to my install. Corey http://www.orangetractortalks.com/forums/showthread.php?p=150500&posted=1#post150500