barts's latest activity

  • barts
    barts reacted to Paul Allwood's post in the thread Just another ballast box with Like Like.
    Added some feet for forklift access and a tube for a trailer hitch. The feet don't quite close the bottom of the corner uprights -...
  • barts
    barts reacted to torch's post in the thread Front loader for a B7200 with Like Like.
    Leave the tractor relief setting as stock. Yes,, some of Kubota's loaders could be had with an optional PTO pump, depending on the...
  • barts
    barts replied to the thread Question for the colective.
    We just made a box beam from 2x lumber, supported it w/ chain and straps and used it to hoist trusses onto our new shop.
    • PXL_20240406_171029805.jpg
    • 1760717534079.png
  • barts
    barts replied to the thread B7200 easier steering.
    I remember doing the calcs for hydraulic steering in a Ag engineering hydraulics course I took 40+ years ago.... but I'd forgotten some...
  • barts
    barts reacted to TheOldHokie's post in the thread Front loader for a B7200 with Like Like.
    My B7200/B1630 combo was generally fine with loaded rears and a -300# blade on the 3pt. Long objects like logs will get you in trouble...
  • barts
    barts reacted to Paul Allwood's post in the thread Front loader for a B7200 with Like Like.
    It appears to work - I'm happy with that so far. Many thanks to everyone who has commented and offered advice so far. I haven't made a...
  • barts
    barts replied to the thread Reducing engine noise on 2350DT?.
    I use a pair of 3M 30 dB ear protectors... these work well, and are less than $25 at Home Depot w/ free delivery.
    • 1758759918907.png
  • barts
    barts reacted to OntheRidge's post in the thread Reducing engine noise on 2350DT? with Like Like.
    I just use a good set of noise canceling headphones.
  • barts
    barts replied to the thread Front loader for a B7200.
    I converted a B219 Kubota loader that was in pieces to fit my B5100. Basically I had to make a new subframe, and devise a drive for the...
  • barts
    barts replied to the thread Front loader for a B7200.
    I used 3/8" line (about 4' long) from the pump to the spool valve; 1/4" lines everywhere else on my B5100 w/ a converted B219 loader...
  • barts
    barts reacted to DaTow'd's post in the thread Oil pressure Gauge install B7100 with Like Like.
    We installed the oil pressure gauge on both of our Kubota tractors using 1/8" npt Close nipple into the block to a brass tee- next the...
  • barts
    barts replied to the thread L175 engine front shaft.
    The shrink disk will compress a sleeve that is solid; it doesn't need to be be split. The shrink disk has a very shallow internal taper...
  • barts
    barts replied to the thread L175 engine front shaft.
    If this setup is similar to the one used on the B5100 tractor, I was able to make a sleeve that just slides over the male splines in the...
    • IMG_20150405_164033.jpg
  • barts
    barts reacted to ken erickson's post in the thread Vevor hydraulic steering unit for B series? with Like Like.
    My thoughts also. My impression is that this system only allows doing away with the traditional cable and pulley system used on...
  • barts
    barts reacted to chim's post in the thread Front loader for a B7200 with Like Like.
    Here is the information on my bucket. I'm guessing it is similar to most others. The tractor was parked on my bridge, one place that's...
Show older items
Top Bottom