Search results

Have around 250 hours on the F3990 and noticed at the start of this season my left rear tire tread is getting thin. Swapped the left with the right and now the same place is showing wear on it as well. It runs fine, steer the same. I do drive it about a mile to from on pavement to use weekly...

Finding specs on power rake at about 15 GPM, and my M9540 at 16.9 GPM. Looking at renting a skid steer rake at using it on the loader. Have a 3rd function lines on the loader. Have two friends with CTL (75hp and 120hp) so can borrow their equipment but if I can do it with my tractor, that is...

Probably dumb question but does the 540 PTO have a min and max rpm range. Pulling my batwing up and down hills the motor rpms change and therefore so does the PTO

Its getting cold so AC not needed, but tried a changes and cleaning and its still not doing good. At idle Low is 50 psi High is 250 psi The above pressure was done on a 85+ degree day and looking at R134a should be about the correct pressures. When I increase the rpms low goes down and high...

Want a box blade that can handle 100 hp or more, and at least 7 feet wide. Been looking around and there are a lot of BB out there but most are not for large tractors. Have a bunch of areas I need to smooth out Look at the LP HR3584 and got a price from Glassgow Kubota and it was $4500...

Have had the mower for about one year and I'm cutting and start seeing black soot over the left (non discharge) side of the mower deck. Its turning everything on the deck black. I stop, remove the covers and don't see anything that might be rubbing the belts. Thought maybe it was a one time...

The mower just has not been cutting at the height the diagram is showing, or at least as I read it. Originally set both front and rear at B-X which should be 4 inches. Have put over 100 hours on the mower and it just doesn't cut smooth and does some scalping. Today I check air pressure in the...

Don't really know why manufactures don't put FF tires on at least the deck. Them small little A's tires are always going flat for me getting next to briers all the time. Both are flat on the F3990 and going to call Barrlow tomorrow to see if they have any in stock. Found them at Walmart and...

M9540HDC24 Not getting any reading for speed, Maybe its just a plug that came off. Anyone know where the sensor is located?

Looking for the part number and figure for the front drive shaft seal. Have been unable to find it, and alludes me how to find it

When Kubota says grease pins every 10 hrs, I would do it. They don't chrome plate the pins so its reg steel to steel. Not sure if loader was ever greased, but there is orange paint on the zerk's. In any case, I have taken a torch to the pin and rod end, and its still not budging. It was...

Tractor S/N 86399 Starting this one to keep track of stuff I do, part number finds, and some questions. Found a couple small splits in the upper radiator hose and was unable to find a replacement using Dayco or Gates catalog Also was replacing fan and AC belts, picked up from Off Road Belts...

Anyone install a HTL on the M9540? If so what size did you install?

M9540 with skid steer attach Looking at several and like the clam shell style. Many list as root rake but I'm not going to try and bend the FEL arms trying to do something like that. Skid Steer Attachment Depot has a 72 inch which looks like what I'm thinking about...

Anyone happen to know what the front drive ratio is on a M9540 SN 86399? Trying to figure out a tire issue and would like all info to compile it

Changing the fuel filter an separator and don't want to break anything. There is a plastic round knob on top of the filter housing which I think it would normally be a primmer pump. Tried to loosen but seems either stuck or there is a pump somewhere else.