Search results

Mark, great link for the wires. What size wire do I order in terms of AWG?

Update guys and big thanks to Dave. After dicking around for a while I finally found the problem. I polished ground at frame connection, still no power. i took positive off at solenoid and cleaned everything up, i cleaned the fuse link connection. I inspected all wiring I could access under...

How do you Tin the area? With solder? I’ll be a couple pictures of my ends today.

So Dave, yes I do have repair ends on them at the battery posts. They were both installed less than 2 years ago when I replaced the battery. You say replace them, with oem? I’m assuming they are a one piece cable? For now today I’m going to look at ground, and clean it. It’s funny because the...

Thanks for the reply’s guys. One other thing to note, on several occasions I would turn the key and begin to see the gas gauge needle moving. It would then stop and fall back. This would happen but I would see no sign of power to any gauges, oil light, etc. I did have the battery tested and it...

Hey guys what’s up, I have an issue. I ran my old b8200 for 3 plus hours yesterday, shut it down parked in the barn. Today I went to move it and I got a click. Tried jumping it nothing, battery tested good. Now the goofy thing is initially I would get power to the dash here and there. It would...

I’m pretty sure it was part of the spline shaft, but maybe it was a bushing. I didn’t try very hard to get it out as i thought it was part of the shaft. With the big square corner the seal would constantly fold over itself on the ID. I ended up using electrical tape to make a ramp from the...

The splines are not the problem as the OD is smaller. It’s the step up onto the smooth bore shaft. I had a thought this morning while eating a ham and cheese omlet. The front diff still has oil in it, the fill and drain plugs are still in place. When I push the seal in it feels like a plunger...

Bump, I need some help on this guys...

I finally got my new seal and roll pins. Took housing off and a bunch of gear oil came pouring out. Once I got to the old seal the inner diameter had a big tear. So I then struggled for a good hour trying to get the new seal in. It’s being a royal pain and I gave up for the night. By hand you...

I haven’t taken the three bolts or the cover off yet. The seal that I was talking about originally was the dumb little dust seal at the end of the protective tube. I hadn’t looked deep enough into the schematics. The seal inside the cover was ordered today along with a couple pins and an o ring...

There should be no water as the case was drained and filled within the last couple of months. When looking in the fill port the very top layer of oil was foamy. I don’t think the axle is cracked as there was only a small bit of oil oozing down the side of the differential, not even enough to...

Hey guys what’s up? I haven’t been on here for a while as my kubota has been dominating all this snow we have in Minnesota. Anyways I ran my b8200 for about 2 to 2.5 hours last Sunday and after I parked it I noticed a puddle on the floor about the size of my fist. A couple months ago i had a...

Yeah it was the most expensive bolt I've ever bought that's for sure. Oh well, I think my only other option was having a bolt made which I'm sure would have been similar in price. I still am confused with Kubota. The replacement bolt they sold me is not correct and they still seem to think I...

Wolfman, you were right. Initially my left cylinder would push, right did nothing. I then removed the entire quick connect for the left cylinder. Now my right cylinder would move and nothing from the left. I then swapped out the female side of the quick connects and same thing. I said f it, I...

Thanks torch for the advice. So today I got roughly 5 more gallons of udt. I filled the tractor and it seems to be full by only adding about 3 gallons of fluid so not all fluid was lost. I did crack the rear banjo open and cranked it over good three times. I never did see fluid coming out but I...

Well I got my eBay special banjo bolt today. Oem bolt and it’s the correct length. I went ahead and installed the supply piping, so it’s back to original design and the goody two holed banjo bolt is out of the picture. Tomorrow I’ll pick up another 5 gallons of hydraulic fluid after my brand new...

Update for you guys. So Kubota is still saying that I have the correct replacement bolt, and they are also saying that the replacement supply piping is no longer an available item. So I look on ebay and see that a guy is selling the 3 point control valve and it has the banjo bolts to go with...

Ok torch and wolfman, I owe you guys a beer. I messed up big, and I did deadhead the pump. I removed the damage last night, and I discovered the goody banjo bolt was not fully hollow! I was so sure but I guess I never fully examined it. I’m an idiot!!! It all makes sense now, fluid went from...

Torch, Wolfman I have a feeling the home made banjo bolt was not suitable for the actual working pressure of the system after I plugged it’s previous path of least resistance. I don’t think I dead headed the pump. Check out my photos. Wall thickness of new banjo bolt that is too short, roughly...