Recent content by coralhead

  1. C

    B7100hst operating temp?

    Thanks, this is my first experience with this type of cooling system.
  2. C

    B7100hst operating temp?

    I have a '93 B7100hst with a 60" kubota MMM. What would the normal operating temperature be of a properly working cooling system? I have a SunPro temp guage to see the temp but the gage fluctuates approx 40 degrees on the needle. The gage is going to be replaced but am looking for a temp...
  3. C

    Radiator Cap question

    I have a '93 b7100hst and want to get a new radiator cap. Anyone know the proper psi cap that is needed? Thanks in advance, John
  4. C

    Name Info needed

    Industry Std size 6201. McMaster Carr # 5972k42. I got the sealed instead of the shielded. Also helps to make sure that the thread and nut assemble freely before installing housing. That way you can fingertip it most of the way and finish up with a wrench.
  5. C

    Name Info needed

    After having my fan bearings lock up on my B7100, I proceeded to remove all the front sheet metal and radiator. I am looking for the name of the designer who put that nice stud/nut that is next to impossible to get to. I was able to bend up a cheap 10mm openend I had laying around and was...
  6. C

    Mower deck under coating ?

    I have just reworked my RC60-71B on my late model B7100 and used Rustoleum Gloss Black and added enamel hardener and painted it on thick with a brush. A lot cheaper than POR-15 but then again it is what I had on hand in the garage.
  7. C

    My project pic thread

    I can get you the file I created and send it to you. The link below should be able to print you out a few for samples. I'll send you the file if you are interested. I am not in the position to have more made since I do not have personal access to a 3d printer. Let me know. John...
  8. C

    I can get you the file I created and send it to you. The link below should be able to print you...

    I can get you the file I created and send it to you. The link below should be able to print you out a few for samples. I'll send you the file tommorrow from work if you are interested. I am not in the position to have more made since I do not have personal access to a 3d printer. Let me...
  9. C

    My project pic thread

    I copied your headlight install but with a twist. I was able to have two headlight retainer rings made on a 3-D printer. I modeled them up and my boss printed them up for me at his home. They worked out pretty nice.:)
  10. C

    My project pic thread

    I picked up a set from O'Reilies today. I will need to get my relay and come up with some brackets to hold them in. I like the o-ring idea. I am almost doing a mirror restore on a '93 B7100 HST. Working on painting the mower deck right now. Thanks for the help and suggestions. John
  11. C

    My project pic thread

    Perfect pictures, That is the way I am going to go. Did you run a hot wire and hook the stock headlight wire to the relay? Thanks a lot for your help. I'll post some pictures when I finish. John
  12. C

    My project pic thread

    Where did you get the new headlights? I would really appreciate some vendor and part # info. Thanks, John
  13. C

    Kubota Paint color

    I am painting my B7100 ('93) and am using base/clear. I have the matched paint for Nason (dupont) if you are interested. It is a formula for a quart. Let me know if you are interested. I also have the oranged matched as well. John
  14. C

    Will 3 cycl start w/o glow plugs?

    The attached print shows the plugs wired in parallel.
See more
Top Bottom