The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
QA Post Hole Auger for B2650
- Thread starter NHSleddog
- Start date
I have the Landpride HD25 auger motor mounted to a SSQA and using a 9” auger. I am using this on a B2301 with no issues, except that I have rocky soil, so I have to go a little slower or I end up binding up. The LP HD25 is a good motor, but I also considered the Danuser PD6 hydraulic motor. I can’t really give any advice on the Danuser. It looks well made, but the dealer convinced me to stick with the Landpride line for most of my attachments. Not sure if that helps.
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
rkidd
Active member
Lifetime Member
Equipment
B2650, FEL With QA 60"mmm, 3pt FDR1672,homemade ballast box, BB 1572 box scraper
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
Looking at the Landpride augers I think that I wood look at the the side of the bucket style. With the smaller tractor you might use a quick attach plate and place a plate perpendicular to the QA and you could increase the lifting height if needed.
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
The Kubota brochure https://www.kubotausa.com/docs/default-source/brochure-sheets/b50rops.pdf for the B2650 says 8.7 gpm total output. You tube from Messick's https://www.youtube.com/results?search_query=messick's+hydro+post+hole+digger shows a B2650 turning one.
Last edited:
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
If I understand correctly you are wanting to use the motor to run a concrete mixer? If this is correct and you buy the SSQA why not mount the motor on one side and the drum on the other and use a gear and chain to produce the desired RPM?Thanks for the link. It just needs to spin a little faster.
I am shooting for 50RPM. The mixer will be happy with anything above 30RPM.
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
Could you mount this https://www.northerntool.com/shop/t...RdvlArHH8i8FfQTmNLJ41dftN0pwLIRBoCPVgQAvD_BwE onto the back and mount the auger to the front end? I do not know what you are trying to do, just trying to think outside the box. I could see extending the draw bar under the rear mixer and pulling a wagon to carry supplies as if you were fence building or something like that.
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
BigG
Well-known member
Equipment
l2501, FEL, BB, Rotary cutter, rake,spreader, roller, etc. New Holland TL80 A
It shows the 2500 unit runs on a minimum of 7 gpm and the B2650 makes 8.7. I am not arguing I was trying to figure out how to read the info correctly. I know enough to know I do not know enough.
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
8.7 GPM is total flow
3.7 GPM is for steering
5 GPM for all other systems
So a b2650 Max could maybe power a 5 GPM min motor.
I say "could maybe" because there are other factors involved that could limit the flow down even more.
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited:
The content of this post has been edited to remove any possible offensive material. Sorry for the post.
Thank an offended member.
Thank an offended member.
Last edited: