1982 L245DT crankshaft splines
- Thread starter Milo Holroyd
- Start date
I know I'm resurrecting an old thread, but since it's just happening for me, it's all new.
Am I right, in thinking this kit would put the FEL back on the onboard hydraulics, and not on the front mounted pump I now use?
Thanks
Tim
Am I right, in thinking this kit would put the FEL back on the onboard hydraulics, and not on the front mounted pump I now use?
Thanks
Tim
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Yes you are thinking right.
Well adding the kit(or Parts) and switching the lines around will move the hydraulic operations to the main pump.
Well adding the kit(or Parts) and switching the lines around will move the hydraulic operations to the main pump.
Last edited:
I must be reading it wrong as I think it all involves the pump on the crank. Good luck I hope you are right as I had to fab my own crank to pump shaft- using part of a lawnmower axle.
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
sullpond,
Sorry I miss informed you, I read the original posting wrong.
The kit they are talking about upgrades the crank shaft run pump and not the main hydraulic pump.
I know on a B7100 you can change the pump to a B8200 pump and gain performance but I have not heard of a similar change for the L245.
Sorry I miss informed you, I read the original posting wrong.
The kit they are talking about upgrades the crank shaft run pump and not the main hydraulic pump.
I know on a B7100 you can change the pump to a B8200 pump and gain performance but I have not heard of a similar change for the L245.
Bringing this thread back to life compliments of the search engine....
Pic's tell the story:
Splines (18) worn smooth on the coupler that goes over the crank shaft protruding out the front of the L245DT.
Trying to find the replacement coupler (18 spline) and repair this one.
I did find this on-line:
http://us.sparex.com/pto-adapter-fe...le-spline-1-3-8-6-with-locking-pin-15073.html
Pic's tell the story:
Splines (18) worn smooth on the coupler that goes over the crank shaft protruding out the front of the L245DT.
Trying to find the replacement coupler (18 spline) and repair this one.
I did find this on-line:
http://us.sparex.com/pto-adapter-fe...le-spline-1-3-8-6-with-locking-pin-15073.html
Attachments
![20200205_115227[1].jpg](/forums/data/attachments/41/41177-f44b5479818e74f82b6f35d98c770fdd.jpg)
Last edited:
I found this on ebay - I am not sure if that would help make the repair. (It appears that this is the wrong diameter)
https://www.ebay.com/itm/John-Deere-Axle-Shaft-Coupler-Part-WN-H165510-4-Long-18-Spline-for-Combines-/253544361706
Last edited:
That one is really close....the inside diameter on the one I have is 1" and I see the JD one is just a bit over that.
I Googled "18 Spline Pulley" and am sifting through the results looking for a 1" inside diameter that I can adapt (ie: cut away the pulley portion, and have some center stock to replace the one I have).
I called the Sparex company, and they are wholesale to suppliers like NAPA and The Tractor Supply Company. Turns out.....that coupler would be well over $100 retail!!!
I searched and I found another post where someone was looking to do the same thing but there was only one post with no resolution. The coupler is probably 25mm(0.984252 inch) x 18 spline as that was what the other poster was looking for -- https://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=rrtips&th=251