Search results

Been try to find an adustable angle grader blade for my little kubota b6000 - I am guessing that 48" would work. Anyone out there find a reasonably priced grader blade? Thanks!

My little B6000 loader has been working great, but in spite of being properly filled (4 inches below breather with rams fully retracted according to manual) the FEL will blow fluid out the breather when hot which is irritating(kinda burps out fluid randomly. I am using a Universal hydraulic...

Just got a message from a new as of this morning member directing me to a guy named Scott Bahena who has a ROPS for my B6000 - Sites like ours are getting trolled heavy from opportunists so trying to vet Scott -anyone buy from him? Oh, and wants me to pay via CashApp BTC - bit coin apparently

Yesterday, after loading up my bucket with 5-6 loads of 3/4 minus, I started to get some pump chatter (cavitation?) I noticed that my return line (low pressure) was twisting and reduced a little in diameter due to air/diminished flow (?) More importantly, my return line has some excess and had a...

If so, please message me, thanks

As the title says, has anyone used the pto setup on a B6000 to power a 12kw Generator (PTO style Gen) Thanks!

Been cleaning up my b6000 that also has the B219FEL. I see a very clean weld repair on both sides of frame under engine and behind front diff - did these frames have weakness issues when fitted with FEL? I am thinking that PO must have overloaded bucket and perhaps hit a hard bump other and...

Hi, anyone have a 3 point hitch off a B6000? Need the wheel/knob that levels the hitch setup -thanks

A good day and well . . . . Adjusted valves and while I was at it, replaced orings in decompression valves that sit in valve cover. What is the adjustment procedure? I see how the little cams act on the top of the valve springs -I am guessing that screw is turned down until it just touches top...

Found there was a wire from light switch (yellow) to AC post on recifier that was missing so soldered in, cleaned up connections and voila, I am now charging. A small blue blue is severed at light switch which I believe will probably be the culprit behind no lights -

I have the feeling that my new to me B6000D is stuck in 4x4 mode - how much upward travel does your lever move when moving up to 2 wheel drive or down to 4x4? Also - same for high low lever located above 4x4 lever - lots of travel or are both levers very short throw style? Thanks!

Been working on this new to me B6000 4x4 - pretty rough, a bit weathered but came with a loader and box scraper, newish tires, etc for 2900.00! Did a full service, had to clean up some electrical wiring issues and noticed yesterday oil pressure light (it was previously missing) was not turning...

Received my oem glow indicator (glowing nichrome wire peephole on dash) - first impressions: the oem wire is easily twice the diameter of the Amazon unit - we shall see . . . .

Is there a common tap size to ream my GP threads - used to have a Mercedes glow plug reamer - cannot find it. I've heard M10x1.0? I was able to back them out with PB blaster and lots of back and forth movement. Both GP's were a little loose which surprised me so no doubt a fair amount of carbon...

Today I pulled my glows as I continue to work through the electrical issues to get the glow system up to snuff. I found a larger wire with a huge female spade running between the valve cover and the water inlet radiator hose connection and for the life of me, I see no male spade to connect to -...

Pulled the dash to sort out the electrical issues for my new to me B6000. PO had wired in a toggle on/off which failed so fortunately, I was able to source a new keyed off on switch (oem!) and spent the afternoon cleaning all the contacts for everything behind the dash - even found a dangling...

Today, I did a series of flushes on my radiator (citric acid flush, neutralize, rinse, etc.) Tractor started perfectly over 10 times. I added new coolant and nothing when I tried to engage starter, no click no nothing! Plenty of volts in new battery (12.58V) - At first, I thought perhaps...

Hello All, my new to me 4x4 B6000 seems to have no square bolt filler plug for the steering box - I have seen other B6000's that have this fill plug. Would like to drain steering box via suction (hoping it is not full of water!) and then refill. Perhaps removal of a bolt will provide access?

Hi Folks, as I dig deeper into this tractor, I am now trying to identify my loader. It appears to be purpose built for my little B6000 - did Kubota make their own FELS way back when and where did they stamp model number? I need to track down a filter (the one mounted down in the post reservoir...

As I clean up and service this (1977 I believe) B6000, I am noticing various things that need to be addressed. The fuel return lines are pretty ancient and i would like to replace those lines between the injectors as well as the line to tank. Have not probed line to see what is or if there are...