Search results

I tied the clutch pedal down and took off the inspection plate and spun the disc with a screwdriver. I took the tractor back apart and purchased a shop manual and found I have to adjust the clutch fingers. Unfortunately there are different adjustments and according to my manual my pto fingers...

tied the clutch pedal down and took off the inspection plate and spun the disc with a screwdriver. I took the tractor back apart and purchased a shop manual and found I have to adjust the clutch fingers. Unfortunately there are different adjustments and according to my manual my pto fingers...

I tied the clutch pedal down and took off the inspection plate and spun the disc with a screwdriver. I took the tractor back apart and purchased a shop manual and found I have to adjust the clutch fingers. Unfortunately there are different adjustments and according to my manual my pto fingers...

Put a new clutch in my M7030SU. have clutch adjusted and when the tractor is off and clutch depressed the traction disc is loose but wont disengage when running adjusted all the way. Anyone run into this before is there something different about Kubotas I am missing in adjustment

thanks Tried to jump the starter and it would not jump went through the harness and found the safety switch was unhooked and the wires haphazardly tied together. Tested the switch hooked the wires back up and running great thanks for the help Cleaned the ground wire to the frame anyway it did...

Thanks Tried to jump the starter and it would not jump went through the harness and found the safety switch was unhooked and the wires haphazardly tied together. Tested the switch hooked the wires back up and running great thanks for the help

Still working on my Kubota now it wont start. Just clicking, Battery is new and tested soldered new ends on the cables getting 13 volts everywhere I check. Noticed the glow plug relay clicks when I turn to start. Also the starter relay clicks but nothing on the starter clicking including the...

I am rebuilding a Kubota m7030su and it has a bush hog quick loader on it. I cannot find any info on how to identify the system. I would like to buy a set of forks for the tractor but not sure which ones will fit any help would be greatly appreciated.

Thank you I appreciate that

I am rebuilding a Kubota M7030SU and am getting ready to have a new clutch installed. I do not want to ruin a new clutch and am not familiar with a manual transmission. I am guessing when I start my PTO with a bushhog attached I should lift the bushhog off the ground a few inches and engage pto...

Manual says not to leave pto clutch disengaged for any length of time do I disengage pto clutch then engage or disengage pto then reengage clutch and leave it engaged when not using pto. Then when I want to use the PTO disengage clutch, engage pto lever then slowly engage pto clutch. ? Any help...

rebuilding a 1997 kubota m7030 I bought for 500.00 Have went through almost the entire tractor so far. A lot of work, I am wondering whatthe creeper gear is for. My old tractor was a compact with hydrostatic so I am new to clutch tractors. The manual says the creeper gear has a high and low but...

Thanks for the reply it was really bugging me. Had me going for sure.

I took the cylinder liner off my tractor because my 3 point arms were staying up. I am going to rebuild the cylinder and the control valve. I cant help but notice the top link bracket has grease fittings in it but the main shaft has pins in each side so it cant move. It has a rod that goes to...

Figured it out thanks for the reply. It ended up being the pump. Took it apart slight scarring on the end plates. I did not believe it was enough to let pressure by but it obviously was. New pump cured it.

Can’t find where the hydraulic line feeds lift cylinder it goes into cylinder liner with a relief valve on top but can’t see where it feed control valve or lift cylinder no lines going to either has to have fluid going somewhere to it checked breakdown doesn’t show anything

Forgot to mention not sure if i had to bleed the steering another way, since it had a return system i thought it should bleed itself with rotation of wheel

New to forum I bought a Kubota m7030su a few months ago and have been working on it ever since. Just rebuilt the steering cylinder because it was shot seals were blown and rod has major damage. It has been sitting for years. Got it all back together and no steering. I rebuilt the cylinder and...