Search results

I changed my HST/ hydraulic filter and oil the other day. I let it run for a couple minutes and checked the oil. It was low so I added some. I then drove it back to the shed and parked it. It is now reading over full. Should I run it for a while then check it again or should I just drain some...

I have one of these on my B2650 one side hooks fine. The other seems too wide is this the right QH for my tractor?

Both of my rear tires are leaking out the liquid ballast. Looks like it’s between the rim and tire. Is there anything I can do to stop it or do I need to take the tire to a repair shop?

I’m getting ready to change my HST/ Transmission fluid and filter .The Owners Manual says transmission case 4.0 gallons. Does that include everything or is there more needed for the hydraulic system. I know they both use the same fluid. Thanks

I keep my LP grappler in a shed. But it gets pretty hot in there. Last time when I went to connect the hydraulic lines. It had some much pressure I couldn’t connect. Is there any way to relieve the pressure other than pushing on the when I go to connect with a piece of wood or a screw driver

I’ve got a 72” rear blade for my B2650. It has a steel cutting edge. IF we get any snow I’ll be cleaning driveways and my church parking lot. Would the steel edge hurt the asphalt or should I look for a rubber edge ………. Thanks

I’m thinking of getting a Burmalight stump grinder. Does anyone know about these and how it would work on my B2650

I’m looking at a Texas Bragg trailer to haul my B2650. Can anyone tell me if those trailers are any good. I can’t seem to find anything reviews on them. Thanks in advance

Can anyone give me some advice on these attachments. Some one near me has a rotary cutter for $1700. But I don’t know anything about them

I’m looking at getting a rotary cutter for my B2650. I’ve looked at Ironcraft and Land Pride. Both are 60” and have shear bolts. Any advice for this newbie. I’m getting ready to retire and want to make some extra money doing odd jobs with my tractor. Thanks in advance

I’m get ready to change the transmission/hydraulic oil and filters in my B2650. Is there anything special I need to know when I do this? Or is it pretty straight forward……… Thanks in advance

I’m looking for a rotary cutter for my B2650. I found someone selling Southern attachments. Can anyone tell me if these are any good. Don’t know the price. Person wasn’t home to ask any questions. Also can I go with a 6’. Or do I need to stay with a 5’. Thanks for any help with this

I’m looking for a rotary cutter for my B2650. My dealer has a LP for $1900 and a woods for $2900. I’m looking around for a nice used one. The fear I have with a used one is how do I know if the drive shaft is too long? Thanks in advance for any help. I’m a rookie when it comes to tractors

I have a quart of Kubota 15W40 oil. I want to start using Rotella 15W40. Would it hurt any thing to mix the two. Thanks

The SSQA is loose on my B2650. Is there any way to tighten it up? I’ve looked at it and I done see any way. But I could have missed something. Thanks

I just brought a 72” LP rear blade for my B2650. When I went to install it. I had a hard time getting one of the lower arms to slide onto the pin. It acts like the lower arm won’t open wide enough to slide over it. Am I doing something wrong or are the pins on the blAde too long? Thanks for...

Im Going to change the antifreeze in my B2650 I’m a little nervous about the pet cock on the block. And the drain in the radiator. Do both of these seal up pretty good? I’m worried about leaks after I’m done . Any special advice would be greatly appreciated. Thanks in advance

I’m looking for a rear blade for my B2650. My dealer said he can ge one in from another store. RB 1572. $839 RB1672 $1039. Is that about right or is that high. Thanks for the help and advice

I’m looking for a rear blade for my B2650. I’ve looked at the LP and Titan. And are confused which one to get. I’m a newbie when. It comes to tractors and attachments

The 3 pt hitch on my B2650 is slow to raise. When I pull the lever to raise it, it doesn’t start raise till I hit 5 on the indicator. The hydraulic oil is within limits. Is there an adjustment or is something going bad. I don’t have but 120 hrs on it