Search results

  1. M

    L1500 issues

    I recently went to sell my L1500, I backed up the the brush hog and attached it then pulled the tractor down to the driveway for the new owner to come pick it up. It ran great the night before went through all the gears tested PTO everytinhg working as it had for the last 2 years. When the buyer...
  2. M

    PTO

    Hello All, I recently was given a agri four 48 inch rotary cutter. I need to know if I buy new PTO shaft does it have to be cut or can it be left long. The one i am looking at goes from 42.5 inches to 55.3 overall safe span. The one that is currenly there is actually about 4 inchs short and if...
  3. M

    PTO

    Thank you so much.
  4. M

    PTO

    Hello All, I have a L1500 that I need to get a PTO over run for but I am not sure how to measure it. It is a 6 spline but I dont know if I need to measure from spline to spline or just the shaft without the splines? Second thing I have seen them in a 1" 1/8 to 1" 1/8 and 1" 1/8 to 1"3/8 and...
  5. M

    L1500 PTO

    I want to thank everyone who has taken the time to reply to this question. Your answers have given me the information to move forward with my next little project. Thanks Mike
  6. M

    L1500 PTO

    So if this thing has a 3 speed PTO as pictured in the attachments which gear should it be run in for bush hogging and which speed for tilling? Thanks again guys, Mike
  7. M

    L1500 PTO

    Sorry didn't see the attachments until after i sent the last message.
  8. M

    L1500 PTO

    Thanks for your reply. Is there any way you could send these pages to me for download. I have a manual for the L1500 on disc but it isn't clear and a lot of it is in Japanese.
  9. M

    L1500 PTO

    Hello All, I have an L1500 and want to run a brush cutter and or maybe a small tiller but I am unsure how to measure the PTO for a over run clutch system. Also I am not sure on how the PTO actually works it has a knob that is marked hi and low but not sure what its for. I have just been using...
  10. M

    Tires for my L1500

    Thanks for the information. Just one more question at 17hp will this be able to use a 4ft brush hog for small stuff (1in to 2 in diam) thanks again
  11. M

    Tires for my L1500

    The tractor is 2 wheel drive. I am guessing it is a manual but it has a throttle pedal that can be used or a lever. Not sure if that would be considered HST or not. Thanks
  12. M

    Tires for my L1500

    I am looking to replace my rice tires with turf tires what size rims do I need to buy to change over to the turf Tires. Also what if I find rims for the L175 is the bolt pattern the same as with the L1500 with the rice tries. If I go to the dealer and tell them I need rims for a L175 are they...
  13. M

    Brush cutter and L1500

    Thanks guys I dont plan on cuttinv any thing larger than about two inches if it's bigger than that I'll take a saw to it. And. It it to the dirt where can I get an over run. Clutch and how much do they cost.
  14. M

    Brush cutter and L1500

    Ok folks, back to the brush cutter talk. I have a L1500 what type of rotary/brush cutter do you all recommend? I have a lot (3/4 acre) that has some small saplings(1/4 in to 2 inch),will my little tractor cut the mustard with the right cutter or do I need a bigger tractor? What type of cutter...
  15. M

    Maintenance L1500

    I have a parts manual for my L1500 but no maintenance manual. I need to change the hydraulic fluid and I need to check the level of the fluid. Also need to know the type of fluid to use same with the oil and filter. Its getting close to winter so I want to get it ready to store as it will not...
  16. M

    L1500 service or repair manual

    I just bought a L1500 or so the owner said it was. I need a few things one since it is a Gray Market tractor where would the serial number be located. Second and most important where can I get a parts catalog for this tractor. I need to replace the toplink plate as the one on it is homemade and...