Search results

A buddy sent this to me this morning, he has a front mount SB on his LX 2610. 🤦‍♂😮🫠

I was looking for a front mount blower for my B2650 other than what Kubota has listed, the 2782. I had a loaner for a winter and wasn’t impressed with the build and performance vs my LP pto SB1064. I looked over the LX series blowers as they are built much heavier like the Land Pride. The only...

My 2650 developed a oil leak last May at around 50-60 hours. I’ve cleaned it up and it comes back after about an hour of run time. I brought it in a week ago. Anyone have this oil leak like this? The oil filter is not the issue. A friend has the same tractor with more hours with the same leak...

This is the second time my front deck (RCK60-30BA) wheels have came off. Today the C-clip came off (which I found) and the wheel went under the deck while mowing. I installed a new C-clip and machine bushing to limp the wheel a long until I pick up a new one. Kinda scary seeing that thing go...

Seen a B2650 Pissin oil/hydro fluid from under the hood. Stopped by and talked to the owner and he thought it was only oil. It was milky so im guessing the hydro pump is pushing Hydro oil into the engine? Bummer!

What’s with the n/min for RPMs on the dash of the B2650 series?

Picked up my new B2650 with cab yesterday.. So far I really like it. There’s no comparison to the weight and power difference while using the loader or blowing snow. The tractor handles the blower vs my BX was handled by the blower. :)

So my Trans leak (2016 BX2670-1)that was fixed at the dealer last May came back again in the same area but worse this time. I’m waiting to hear back from him as he wanted to charge me last time around for warranty work approved through Kubota. I’m thinking it’s time to trade up and buy a new...

Changing my left axle pivot seal as soon as they arrive from Messicks. I plan to replace my fresh UTD oil in the front case with 80w-90 as the books also calls for. Anyone else using gear oil?

I seem to be scalping my lawn while turning on slightly uneven ground. My dial is at 2. I had the anti scalp wheels up around a 1/2 inch or so from the ground. They did seem a bit high. I went down 1 notch and see how it does next cut. It cuts great on flat ground. The fine adjustment bolts...

I installed these yesterday, they should come in handy. I painted them as they come gold color from the zinc coating.

My trans leak came to around $1000. The parts were $56.00 and the rest was labor, besides $28 in shop supplys Dealer said the leak is covered under the drive train warranty but, I am responsible for 25% or $250.00. If I trade up to a new tractor he will eat the $250.00 I can not find anything...

Stopped by the dealer for Demo days, talked to the Tech that is changing my driveshaft oil seal on the trans side. He claims the entire trans has to come out to install the new seal. I guess this is good because I swear the leak is higher up than that seal and he claims its just the drive...

I noticed my front diff oil seal is weeping and my trans oil seal is leaking a bit. The trans side is a little worse as it has a occasional drip. I cleaned both areas up and will keep a eye on them. Is this the norm for the drive shaft seals? My Can-Am Commander would do this also at the...

How bad is the install of the Power Beyond on a BX2670 ? I’m looking to add rear hydraulics for my rear blower chute rotation. I’m not finding much for prices on Messics or Germanbliss web sites.

Looking to pick up some M8x50 class 1.6.6 spare shear bolts for my SB1064 rear blower. These are impossible to find unless you go through LandPride. Anyone have any sources?

A friends JD 3320 with 1015 hours lost its pto. The repair was to replace all gears, shafts and bearings. The issue was the bearing journals had broken causing gears and bearings to come apart. The repair took 20 hours labor and a pto kit along with a $87 filter. Hard to believe it had a...

Farm King rear PTO 540 rpm blower for sale. Freshly painted and in perfect working order. New Farm King PTO shaft ($460) 3-point on the blower is adjustable in length. For Tractors 18HP and up. Call or text NineZero6 3six4 850Zero Located In Bessemer Michigan. $1350.00 Moderator note- contact...

I found a SB1064 that’s 3 years old and like new. I can’t pass on it. The local Dealer said he would give me $1300 trade on my 60” Farm King blower when I called for new prices today, so I though it would be a good time to sell and upgrade.

I picked up a used Farm King 600 snowblower, it seems to have a general use pto shaft on it. I need to find a pto shaft with a sheer bolt on one of the knuckles. Anyone have a link to who sells them? I***8217;ve looked at the normals like TSC, and other end Tool with no luck.