Search results

Have you bent any pins? Also, did you weld nuts to the back support or tap the tubing etc? A great build!

Your use of form stakes is a great idea which has solved my problem. Great Looking Shop! Thanks, Bill

Found jbolt001's DIY Straw Bucket and think that the use of concrete form stakes is the way for me to go. I'll use 1 1/2" square tubing for the frame and 3/4"X36" form stakes on 4" centers for tines and will attach it to the bucket. jbolt thanks for the idea. I feel guilty for the theft but will...

I built a pine needle rake which does a good job but I am loading the front loader and shelf by hand. I am thinking about building manure forks for the front loader with 1"X1" bar stock 16" to 20" long tines but am concerned about tine spacing. My road is 1/2 mile from the far end to the burn...

I made a rake to remove pine needles from my road before grading and preparing for snow plowing. I have used a manure fork for years but now need a front loader debris/manure fork to pick up and load them. Any ideas and photos would be greatly appreciated.

Negative Wolfman. My problem is the seal between the axle flange (8 bolts) and the axle ( 2 studs and 4 bolts that mount the wheel and tire). This morning I used the same chisel and hammer as yesterday, 2 strikes and the collar popped off. Maybe I was holding my mouth wrong. Thanks, Bill

I used the grease gun for my chainsaw and it worked. Thanks for the responses. Bill

I have a 2000 L2500DT with a leaking axle seal. I have removed the axle flange #31353-4411-0, bearing # 08101-06206, and bevel gear # 31333-4394-0. My problem is removing the cir-clips (split collar?) #37650-4368-0. I have bent picks, small screwdrivers, etc. with no results. Anyone here have...

Flintknapper, Those are the grease fittings. With the boom fully down mine are off just enough to loose some grease while servicing the loader. I think my only option is to enlarge the two access holes.

I waste more grease than I apply to the pins in the rear of the booms. The zerks don't line up through the access holes. I have put the bucket in the dump position and raised the tractor with the loader and still can't get a straight shot at these two zerk fittings. I am thinking about grinding...

WANT TO BUY A BRUSH GUARD FOR AN LB400 LOADER ON A 2000 L2500DT KUBOTA. Sorry about all caps. Thanks, Bill

Thanks for the response Wolfman. I'll go with it. Bill

What hydraulic/transmission oil for 2000 L2500DT manual transmission?

I need Kubota orange paint for my snow plow. What have other used that has lasted? thanks , Bill

Shopmaster This is a year old but I was wondering if you had an easy way to install the hard seal on the pistons. I rebuilt one on my L2500DT seven years ago and installed the hard seal by lubing the piston and heating the seal in boiling water. It was a difficult task and I must now rebuild...

I am rebuilding the bucket cylinders on my 2000 LB400 loader and can't find a shop manual for this unit. I was hoping to find an easier way to install the hard seal on the outside of the pistons, or a special tool. The last time I heated the seal in boiling water and lubed the piston with...

Marty394 Please post some pictures of your driveway maintainer. I believe in BUILDITYOURSELF for two or three times the cost and twice the weight! Thanks, Bill

Wolfman Thanks for the quick reply. I will contact Cd'A Tractor today. Bill

Where can I find a parts diagram, parts manual, or shop manual for a Kubota LB400 front loader? Is there such an animal? I checked this site, the Kubota site, Messicks, and several others with no luck. Thanks, Bill

I need some ideas or pictures of forks etc to attach to my FEL so that I can pick up/load pine needles. I built a rake to collect and pile the needles, but I have to load them into the FEL with a manure fork. Any and all ideas are greatly appriciated! Thanks, Bill