Search results

BX2360 with 60" deck. Won't go high enough to rotate height gauge to top, and past it. I can rotate through all the heights, but when I get to 4", it won't go into top so I can go to lower heights. It seems deck won't go high enough. I've taken deck off and put back on. There does not seem to...

BX2360. 60" deck. Took blades off to sharpen. Putting them back on, no issues with side ones. Middle one, when I block blade to tighten, the associated spindle shaft spins before proper torque. So, that spins and I can't tighten. This is with the wrench, not gun. Belt seems appropriate...

I have a BX2360. I'm entertaining getting an Auger. I'm in the very beginning stages and haven't found one, and am just assuming I could get one for a BX. However, before I get too far was hoping for some feedback. Basically, would an auger put too much stress on a BX? Maybe things have...

Been thinking about doing this for a while. Spray can of Herculiner. I’ll post the before / after and then post my rationale I don’t have a garage or outbuilding so I park my tractor under a raised deck. That offers some protection but not much. I’m in the Midwest and we get very cold to...

I have some rust on the floor of my BX under the mat. Can someone offer suggestions on how to repair this, or point me to a resource? Everything I’m seeing is for cars / trucks. I’m not too concerned about how it looks, and more just want a practical repair. Not sure if I just sand down and...

BX2360 60” MMM Trying to find best height for anti scalp wheels. For a couple years I’ve been running them pretty low because I think I misunderstood the manual. So I check out the manual, for 2”, which is where I do most my mowing, seems to want them at the bottom 2 or 3 hole. This is much...

Leaking hose on the middle arm of the front loader. It’s near the connector but seems to be coming from the longer metal tube near the connector, and not the connector itself. The elbow and nut area seem dry. It seems to be coming out of the opposite side (from the nut) of the tube. You can see...

A few years ago I changed to R4’s for my BX2360. When I did that I got them with rims from the dealer. The back ones have went bad and need to be replaced. 1) Can I replace just the back tires if I am going with the same size? 26x12-12. 2) if I get that same size, am I ok finding something...

Could someone explain to me how to tighten the deck belt? Also, how to know when it’s ok to tighten vs change, in which case I would also ask how to change. I know this is basic, but I’m not sure. Numerous searches on here, and elsewhere, are not showing me what I’m looking for specific to a...

BX2360 with 450 hours. Temperature gauge shoots up to red, or close to it. This happens sporadically when tractor is not working hard, in low temps. I’ll turn it off for a minute, turn back on and gauge goes back down and is fine. That and that this happening when engine does not feel hot leads...

The area of both front mower deck wheels is damaged. Looks cracked. I noticed it when I was taking it off, and not sure when it happened. 1) Can this be welded? 2) How unusual would it be that this happened to both sides? The only thing I can think of is some driveway leveling work I did...

PTO lever has become increasingly tougher to move. Still engages it, but sticky. Worried it’s going to become a problem. It’s the entire range of motion. After tractor gets used for a while, it loosens up and isn’t an issue. I’ve looked for an obvious place to lubricate / grease and nothing...

Is there an attachment that would work well picking up gravel from grassy areas other than a landscape rake? FEL would not work either. We had 9” of rain in a few hours and it washed a lot of gravel into my yard. I have a huge gravel path probably 500’ or more. I did some the old fashion way...

Brought a used wood splitter home. Noticed when I got it back some hydraulic oil had leaked from the plug. It was a long and bouncy ride, and won’t be normal. Should I be concerned about this? I thought this system should be pretty sealed for pressure? I would have thought that a metal bolt...

At least once a year I take the blades off my 60" MMM for my 2360 and sharpen them. Never fails that after I do this I hit the random hidden boulder, winter raised stump or railroad spike (why are these even laying on my property?). Then I either take them off again or just worry that the...

BX2360, five years old with 460 hours. I was doing an easy mow today, about 40 minutes in when I saw the needle on red. I'm normally a freak about watching gauges, but today didn't so don't know how long it took to get to red. It's about 85 degrees here. Fluids all good. Belt and fan look...

Just a question about maintenance regarding the front axle on my BX2360. More specifically, the metal bar running in front of the axle (I don't know what this is called). On each side there is a joint with a rubber boot over it. Both my rubber boots are pretty worn and on one side degraded to...

BX2360 stored outside in Wisconsin (under deck, tarped). It's been cold, around zero and negatives for days. Today it's around 14F. Did not have engine warmer plugged in. Started fine, then goes into convulsions. Shakes violently until it dies. Idles around 1000 and unresponsive to increase /...