Search results

I often drive near bushes and trees with low branches and the exhaust pipe have been catched by them. Sometimes even bent :mad:. I thought about adding a stabilizer. But then I found a flexible exhaust connector together with a short slightly bent exhaust pipe at my local car parts shop. Now no...

I have my Kubota B6001 (with 20 HP D950 engine) on the Spanish island of Mallorca. I have no FEL on it. Searching for a not too expensive FEL in Spain, to mount myself, I found THIS FEL that is attached to the front of a small tractor. The manufacturer say that they will adapt it to almost any...

The hydraulic tube to the 3 point linkage started leaking oil at the banjo fitting under the pump on my B6001 (with a D950 engine). I found a small crack. Replace the whole tube or repair? After some time on the net I decided to silver braze it. Last time I did this was fifty years ago! ;) First...

I just saw a new thread on Buying Advice, Recommendations & Pricing with the title "must have websites" asking for links to websites for things like implements and accessories. Many tips are coming in. :) Would it not be a good idea to have a link gallery on OTT there you could add links under...

Increasing width by turning wheel center? Is it possible to reverse the rear wheel center on my B6001? :confused: If so, I could increase the width with about 5 centimeter (2 inch) on each side making my tractor more stable. :) Anders

The simple front weight design in my earlier thread worked but the front end was still not firmly placed on the ground with a heavy back load. I went to the local iron merchant and bought two pieces of steel 400 mm long and 100 mm square each with a weight of 32 kilo (about 70 pound). Welded a...

My B6001 started to lose ground contact with the front wheel when my rear box was full of firewood. I when understod that I needed front weights. I looked at what was laying around and found what remained of a alternator from a generator. I when soldered a 180 mm bit of L-shaped iron to it and...

My B6001 with D950 engine have an small internal toolbox in front of the gearbox. Any suggestion on the optimal assortment of tools to fill this box? :confused: Anders

Anyone knows the thread size of the grease nipples on the 4WD front wheels on a B6001? 06613-20010 and 06613-10010. Is is metric or other? :confused: Just trying to find alternative source for them. Anders

I was looking for a Tachometer for my B6001 with a D950 engine. The engine got a fitting for a mechanical tachometer but a suitable meter was expensive. :( The digital tachometers on Ebay were inexpensive. I bought one with sensor for about 13 dollar. First I fixed the magnet on the front pulley...

Dont know if this is the right subforum for my question? I just bought a B6001 4WD which had the silencer mounted forward which I suppose is the most common way. My experience is that the exchaust gases sometimes tend to get in my face. My MF35 back in Sweden have an upright silencer as most...

I have a B6001 with a D950 engine. It is not charging the battery. I have not yet tested the alternator (dynamo) but I suspect that the regulator is bad. When looking at prices for a new Kubota regulator I found these pretty high! :eek: Are there alternatives to the Kubota regulator? I was...

Inspired by 300zx I decided to make a simple mount for a hour meter. :o I bought a 2" Round Hour Meter on Ebay for about 10 dollar and locally a suitable rubber lined pipe mount plus a u-bolt clamp fitting the steering column. The hour meter is not something you look at when you drive! :cool: I...

Does anyone know the size and thread of the drain plug for a D950 engine? :confused: I am trying to find a magnetic drain plug of the right size to replace the original plug. Could it also be useful to replace the other oil drain plugs in my 4WD B6001? Anders

I understand that some models of the B-line have a auxiliary hydraulic port on the 3 point hitch which you can turn off or on. On my B6001 there is a port but no handle to turn it off or on. Can I fix the three point linkage and use this port for a single acting cylinder, or a double acting...

When seeing all the excellent fabrications in this forum I feel embarrassed presenting my simple project. :o But everyone cannot be a master mechanic so I hope there is room for us beginners also. ;) I have just bought a B6001 (with a D950 engine) and as I have no trailer I needed something to...

With my newly bought B6001 came a rotavator S1000. It looks as this is made to fit my tractor with a very short connector. I understand that there is something missing to the back of it. I have not been able to find any manual for it. Anyone got more information on this rotavator? :confused...

Hello everyone, I am new to this forum as I just have bought a gray market B6001 on Mallorca, Spain. I was told by the previous owner that the engine was not the original but a stronger one. He could not give me any further details and I am not fluent in spanish so I could not cross examine him...