Search results

  1. G

    L4060HSTC PTO Pressure

    I want to test the pressure because sometimes the PTO takes about a minute to shut off. I always start and stop the PTO at idle speed. The test port threads are PT 1/8. I am having trouble finding a test kit with that size fitting. I have a gauge that is 0-600 PSI with 1/4 NPT.
  2. G

    L4060 HSTC PTO takes a minute to disengage sometimes.

    I have a 12' woods finish mower. I always engage and disengage the PTO at idle. If the mower keeps spinning and I put it is some tall grass it stops. If I wait a minute it stops. If I rev it and back to idle it stops. It is not electrical because I can get of the seat and the tractor keeps...
  3. G

    L4060HSTC Seat with good lumber support.

    The arm rests on the stock seat is 23" wide. You can go wider than that. The stock seat has 4" of travel. I called 3 Kubota dealers asking about the air ride Kubota seat. One dealer said the stock seat is great and they never sold the air ride seat. 2 dealers said they have sold them but...
  4. G

    algae in fuel

    My water separator was getting algae in it. I am using PS Bio Kleen. The big pieces on the paper towel is grease. The small stuff is algae. I have 6 5 gal. gas cans. They have maybe a pint of fuel left in them. I emptied them into the coffee filter and found grease and algae in the cans. The...
  5. G

    L4060HSTC fuel tanks.

    I think I had around 6 gal. in the tanks. I got about 1 gallon out of the RH tank. Their is a check valve in the 2"+- line that goes between the tanks. I had the RH tank on the floor. Over night it put about 4 gallons in the RH tank that I sucked out. Should the RH and LH tank have about the...
  6. G

    HST4060HSTC

    Error No. 90 HST-F Solenoid NG. I ran over 1 stick. It made it between the brake rod and the main oil line. Ripped the wires out of the servo regulator. I think from Kubota you have to buy the whole harness. I don't if their is a +- on these. I would like to buy the plugs with 6" of wire...
  7. G

    Front wheel bearing fail L3540

    I broke the outside bearing twice. The first time at 1350 hours hauling heavy clay. The second time at 1900 hours moving snow with the bucket. The second time was a light load. I don't understand the second time. I am using 80W 90 oil. It was full.
  8. G

    The BEST Way TO Perform a Parasitic Draw Test

    I see a lot of people that have issues with electric troubleshooting.
  9. G

    Bacteria in fuel

    I bought a 2017 4060HSTC with 107 hours on it on 06/19/21. On 07/09/2021 I noticed some junk in the water separator an started treating it with PS Bio Kleen. On 10/10/2021 today I to the water separator apart and I am getting a little junk inside the screen. The tractor has 250 hours on it now...
  10. G

    Good Fuel Can

    You just push it down. It opens the valve. It dumps 5 gal. of fuel in 1 minute and 15 seconds. Some cans will not empty all of the way because the light is in the way.
  11. G

    Modifing Land Pride rotary cutter.

    I bought a used L4060HSTC that came with a QH15 quick hitch. The brush hog says quick hitch compatible. It is with this kit. You don't get much float and harder to hook up than the tiller. I bought the black cast iron piece above for $23.00. I shorten the vertical pieces 2 3/4". The...
  12. G

    Added front and rear cameras to L4060HSTC

    The wiring is run with the factory wiring as much as possible. The cameras came from rear view safety.
  13. G

    Can you regen early?

    I am thinking while I am tilling I am using a lot of HP. The tractor is a L4060HSTC. The PM is 23% right now.
  14. G

    How do I check out a used tractor for any liens and if stolen.

    I found a L4060 cab with 108 hours. He seems like a great guy. He has 3 acres. He says he did some landscaping around the house. Everything looks like it has never been dirty. The paint is on the bucket lip. The flashing is on the tires. The engine oil is cleaner than my L3540 after 1 hour of...
  15. G

    Chain tensioner mod on Land Pride Tiller

    I could not keep the chain tight. You have a pivot with a jamb nut that you tighten to 400 ft. lbs. There is a 1/2" diameter rod that goes against the chain. I tighten the nut up with a 8' pipe on the wrench. I had a friend machine a spacer for the idler sprocket. Part #23 is the rod that...
  16. G

    2008 L3540 Instrument panel lights

    The H-DS High Range (Rabbit) Light does not work. The High and low range does work. Is it a replaceable bulb? Is it a big job to get to it?
  17. G

    ZD1211 Gauges

    I upgraded from a ZG327 to a ZD1211L. I have 14 hours on it right now so this is not long term. The 1211 rides a lot smoother. The seat is a lot better. I like the 72" cut but it easier to scalp places. Kubota should start over on the gauges. It charges at 14 volts but the gauge maxes out...