Search results

1987 L2250 4wd, FEL, manual trans. Was clearing a property today - bush hogging, pushing out debris, etc. Tractor stopped driving. Put in gear - sure enough, checked hi/low linkage - yep - engaged properly, put in forward or reverse on lever to left of steering wheel - ease out clutch and...

I had not thought of Fastenal - used to have an account there - years ago. Also - interesting video of splitting one of the studs. Thanks both to answering.

On my L2250 - had an incident where the studs loosened while seeding 14 acres hay - long story short - I lost 3 studs in the field (one stud was always missing) and was able to salvage 2 studs holding the wheel to the hub. I stole one stud from the other side installing the 2 remaining and the...

Thank you!

Over the rear PTO is a fill inlet. I opened it the other day and I can not see a level. Clearly needs to be filled but without a dipstick of sorts - not sure what level to fill to. Also - what viscosity does it need? Can I use UDT? Thanks,

I have a Bark Buster - today I broke the steel tip off. Since parts are no longer available, I'm, trying to figure out how to repair the cone/tip. Picture shows a section of the cast aluminum cone split into 4 sections, the steel tip shaft sheared off at the roll pin. The shaft remaining is...

I have a bark buster and today broke the tip off - the cast aluminum cone broke in 4 pieces where the steel tip connects to the cone. Any recommendations how to fix? Not like these cones are readily available. picture attached.

Arms drop fine. How do I pressure test? And where is the pressure relief valve located? Is that under the seat

I have a 1987 L2250, 970hrs, pretty well maintained by previous owner (i know the guy). He did replace the hydraulic pump over the years and general maintenance expected. New hoses when needed, all fluid/filter changes. Yesterday I bought 2 round bales (hay), they weigh roughly 600lbs each. I...

Thanks for the YouTube tip. Here it is. https://youtu.be/UI_1E0xpofI

Today, mucking out an alcove and piling up manure hay matter, i noticed my dash lights started intermittent doing a low flash. Low being dim. Im guessing a ground is at fault but figured Id check with yall. I tried to upload a short movie clip but cant load a .mov file type. Seemed to only...

I have a belly mowner off a B7100. RC60-71B. Includes front and mid mounting harness. Im in Maryland though

Im selling my tractor B7100 HST-D but the guy diesnt want the bushhog ir MmM. MMM is a Kubota RC60-71B, gearbox rebuilt this past summer, includes mid and front harness. How much are they worth on the used market?

Have you had it on a trailer yet? Curious how it holds up under a wind load? I bought a L2250 that, for me, needs a canopy. But I transport my tractor a lot so I need a canopy to be strong enough to resist the wind load too. I was seriously considering building the canopy frame out of...

I have a L2250 I need a canopy for - but I wanted a large - well covering canopy - something like what Bambam31 did - I was wondering though - how it would travel on a trailer - I transport my tractor a lot - definitely don't need it "sailing away" - ripping off the mount and God forbid -...

I have a L2250, the Kubota loader is BF400G. There are a few shops in PA that sell the BF400G used. May be able to find a Woods to fit as someone else suggested

Trying to find a Service Manual for a 1987 L2250. I checked KubotaBooks - its not there. Any suggestions?

Pictures. Body shows 30 years of use - plenty of dents and faded paint. Some surface rust. Front loader is a Kubota BF400G - bucket had some hard use. Tractor has 897 hours on the working hour meter. So - 30 years old and 897 hours. Tractor was built late in 1987 based on the serial number...

A buddy at church is selling his L2550 4wd with R1tires, 1000 hrs, FEL & backhoe & 5 foot Bushhog, pricing around $8000. I use my 1994 B7100 (no FEL, has R1 tires and just had injectors and GPs replaced, has 1000 hrs) to do about everything I can convince it to do or rig it to do in some way...

As of this morning, I called Messicks.com and found out 'user error" of their website - yep - I was entering a model number in the parts search - that is why the mower deck came back as unlisted. They got me straightened out and I got my new shims, bearings (upper and lower) and new oil seal...