Search results

  1. dotty

    Summit 3rd function on LX2610

    my Summit third function kit for a LX2610 has only one copper banjo washer. how does the bottom of the fitting seal on the threaded hole? Thanks.
  2. dotty

    Wanted RH (adjustable) lift rod for B7100hst

    Re: B7100hst This is what I'm referring too.
  3. dotty

    Wanted RH (adjustable) lift rod for B7100hst

    Can anyone tell me where to buy a leveling box for 1993 B7100HST?
  4. dotty

    B7100HST cooling question

    Yes, it is variable speed. When engine is cold the pumps runs for 10 seconds off 30 seconds at 6 volts. At 36 F below setpoint pump runs 10 seconds off 10 seconds at 6 volts. At 9 F below setpoint pump runs continuously at varying speeds to control temperature to setpoint. The magic of...
  5. dotty

    B7100HST cooling question

    Remote water pump info
  6. dotty

    B7100HST cooling question

    I just installed a Davies, Craig electric water pump with controller on my B7100HST. It took a couple of afternoons and several trips to Autozone for hose, etc. So far it works well, no overheating even after lugging engine with box grader. $400 online from Pegasus Auto Racing Supplies...
  7. dotty

    B7100HST Hydrostatic Pressure Relief

    Does the hydrostatic transmission on a B7100HST have a relief to atmosphere on the right side? I noticed when mine gets hot a little oil spits out of a little thingy on the lower right side. Just enough oil to cause dust to sitck to the front axle housing.
  8. dotty

    Does the hydrostatic transmission on a B7100HST have a relief to atmosphere on the right side...

    Does the hydrostatic transmission on a B7100HST have a relief to atmosphere on the right side? I noticed when mine gets hot a little oil spits out of a little thingy on the lower right side. Just enough oil to cause dust to sitck to the front axle housing.
  9. dotty

    Confused again

    I cannot find the hydraulic system gpm and pressure in my B7100 HST manual. I thought I read that it is 3 gpm @ 2200 psi. Does that sound right?
  10. dotty

    Confused again

    I think I need to take the cover off of the hydraulic block in front of the brake pedals and replace it with the series adapter supplied by the FEL manufacturer (Koyker). Any comments?
  11. dotty

    Confused again

    I am having a front end loader installed on a 1992 Kubota B7100 HST and am confused by the hydraulics. Will the pressure for the loader come from the Directional Control Valve, Hydraulic Block.....or what? I have a Massey Ferguson with a loader and the pressure comes from an after market...
  12. dotty

    Belly mower

    I own a 1992 B7100 HST with a 60 inch belly mower that I am getting ready to have front end loader mounted on. The dealer/installer told me that most belly mowers can be locked in the raised position so the 3 point hitch can bre used for other implements without remover the mower. I don't have...
  13. dotty

    B7100 HST PTO's

    How about a propeller and wings? Maybe the thing will fly.
  14. dotty

    B7100 HST PTO's

    Thanks, that is different than anything I have ever used. Do you ever use the mid and rear PTO's at the same time?
  15. dotty

    B7100 HST PTO's

    I recently bought a nice little Kubota B7100 HST with belly mower. I am experienced with larger tractors and find them all to work about the same, but this B7100 is a little quirky to me. I have the original Operator's Manual but am still confused by the mid and rear PTO speed lever. Does the...