Search results

Found my steel expanded metal, a little more than I thought I had, but worked out just right.

Hi everyone, thought I'd show how thing are progressing slowly on carryall. was able to find some almost Kubota gray and had to evited a few squatters in some PVC pipe/ tool holders with Chain saw holder with last of paint thinned out to far, but has a little color ;).As I was doing a walk...

It's made by Precision Manufacturing

Just a quick shot of Small (27") Add-A-Grapple on my BX2380. Wow, yes there will be a learning curve! But will assist in taking care of task around place. A lot easier moving brush pile then log (firewood branches) or a little better arranged.

Finally got around to mounting toolbox to ROPE. Used 5/16th Insert=a-threads in existing holes. Won't open pass 90 if displaying caution triangle. Almost got close to Kubota gray... close enough. Red balls are for Jeep when pulling into shop.

I also had a hard time researching about Maletti mowers, I ran across larger ones. most of the ones I saw on google were 5 foot and larger. I found parts that worked on them. The consumables seem to be going up in price with their popularity. Lifting a under 4-foot mower (manual suggest 42...

Decided to go with one more 2x8 on headboard and now needing to salvage another 2x4. Decision still out on shorting deck length, but with side rails decision is being made

Started assembling my carry all project a couple days ago, using the Yintatech 3 point pallet forks as a building platform. Here I have a 48x48 deck with 22inch high back board,, I may go up another 2x8. I do plan on adding a couple handled tool holders and lets not forget a chain saw Scabbard...

Looking at older 42 inch mower with PTO shaft, What I can tell from poor photo, grass blades need replacing (fairly beat up and bent. Their held in by cotter pins not bolted like I've seen others. rotor appears straight along with rear roller. Seller is asking 900.00, blue fading in color, with...

?, if your referring to me saying takes "5/16 Allen tool". Which is used to hold bolt in place while torquing nut in place with blue lock tight, just because it was there. It's a blank hole that I put the bolts through. Kubota hardware kit for lip install kit (carriage bolts and nylock nuts)...

Thanks, Kubota's bolt on bucket lip is pretty good and the stock edge is fairly durable and hold up. My older B5100DX lip held up well. The only reason I installed was because it fit better on my BX then holding the wall up :)

Back in December 2022 right after I purchased my BX2380 I purchased a six foot bucket cutting edge. My plan was to shorten and drill and counter sink Machine Allen head bolts with serrated locking flange nuts. Well, I finally finished it up after having extra flange nuts after completing wheel...

Decided to keep JD wheel weights, with a little color not bad at all. My choices were orange or a close Kubota gray. used 1/2 ready rod, oops all thread for you younger folks :) Tacked serrated flange nut on one end for inside of wheel and locked down with another flange nut on outside, four...

I've been closed minded or just stubborn on left side mount. Thanks, need to get out a piece of measuring string :). with the hoses in this configuration, there were times that they came in contact with QH while using rake and placing it.

Thought I'd share, tighty up manifold and wiring. I also shared with Summit about excess Hydraulic line on BX2380 with pictures. You can't always fix long lines by looping them. In the Bx's case, long but not enough to loop. Quick hitch is out for now.

I learned my lesson years ago also, when glancing a engine manual and miss took inches for pounds and broke an piston oiler on a performance motor I was building, which cost me a week. Thanks for link, it gave me an idea to check AZ auto parts, they have free tool rental. Not doing projects that...

I changed one on the bench before mounting manifold, but thought I'd wait until after mounting system on Ropes. Not sure if it will clear coupler, I'll give it a try. I was thinking just one end. It would all depend how my wire placement goes. Did you ever fine a torque wrench to read 2 ft...

Well I'm on the last f of installing 3rd function on BX2380 with rear remote. Looks like I'm going to tape into the systems optional 3rd function fuse position. Hopefully they already have it wire, I'll just need to trace over to where the factory taps into it for their 3rd function unite. I...

Nice write up. just completed running my BX2380 and making sure no leaks per instruction after mounting rocker switch. I also have narrow ROPES but in my case, I just ran a die over supplied bolt. Thank goodness they attach a PDF file. There was a few other questionable order of operation, but...