Go Back   OrangeTractorTalks - Everything Kubota > Search Forums

Showing results 1 to 17 of 17
Search took 0.01 seconds.
Search: Posts Made By: B7510
Forum: Buy, Sell & Trade 08-03-2019
Replies: 0
Views: 278
Posted By B7510
FOR SALE 54" Pin-On Loader Bucket $600CDN

As new. For LA504; LA534; LA403; LA434 Kingston, ON
Forum: Tires & Wheels 11-29-2011
Replies: 16
Views: 5,918
Posted By B7510
Re: Tire Ballist

It's always surprising to me how quick folks are to take advantage of a cost savings up front and gamble on paying "piper" down the road.
Forum: Implements & Attachments 10-18-2011
Replies: 3
Views: 1,924
Posted By B7510
Re: Help needed with a B2789 Blower

Thanks for the picture jb
Quite helpful and I very much appreciate it.

I broke down and ordered the manual and parts info from a Kubota dealer.
Forum: Implements & Attachments 10-16-2011
Replies: 3
Views: 1,924
Posted By B7510
Help needed with a B2789 Blower

:)ISSUE ADDRESSED:)

I need to install the chute on the blower and wonder if anyone can lend a hand as to the correct position of the various hold down and spacer plates. I am confident that I can...
Forum: Buy, Sell & Trade 10-16-2011
Replies: 1
Views: 2,894
Posted By B7510
Smile No longer required - B2789 Manual needed

No longer needed. I broke down and paid the price for a manual.:eek:

Hope someone can help me. I just acquired a Kubota B2789 blower for my B7510. I would like to source a manual and/or a parts...
Forum: Implements & Attachments 07-28-2010
Replies: 14
Views: 5,957
Posted By B7510
Re: Leaving box scraper installed all the time

You can use your "BS" (Box Scraper) for a counter balance or load a 3ph mounted weight box full of "BS" (you get the idea) :) of the same or similar weight to do the same or similar job. If you...
Forum: Fabrication & Customization 03-22-2010
Replies: 36
Views: 13,017
Posted By B7510
Re: Skid Steer Attachment Plate

I have been considering doing something similar as well. I guess there are many ways to go depending on many circumstances. Here is a link to a site which has some solutions you may want to...
Forum: Service, Repair & Maintenance 03-07-2010
Replies: 4
Views: 2,111
Posted By B7510
Re: landscape rake

Hi Dusty
Not sure if this will help. I purchased Landpride rake used in the US a few years ago for my B7510. It's a 6' but works fine. I think its the best thing since sliced bread. I was lucky...
Forum: Off Topic 02-18-2010
Replies: 22
Views: 4,676
Posted By B7510
Re: Snow man

Thanks Dusty for the link
That's a great idea. Don't want to change your Snow Man thread, but is the part that pins on to the fel available commercially, or maybe used?
Forum: Off Topic 02-17-2010
Replies: 22
Views: 4,676
Posted By B7510
Re: Snow man

What a great idea! I'm glad you took advantage of the day for the purpose for which it was intended. Good on you guys and the snowman. Pin a medal on the instigator.:) and the on all the...
Forum: Service, Repair & Maintenance 02-09-2010
Replies: 11
Views: 3,413
Posted By B7510
Re: Help Selecting Tranny Oil - B6100

Universal Dynamic Tractor
Forum: Fabrication & Customization 01-30-2010
Replies: 6
Views: 3,353
Posted By B7510
Re: Finally 6' snow blade earned 2 Wings~!

I think the wings are a fantastic idea! You now have a "snow/plow/pusher" at you fingertips as you require. I hope the wings keep you from getting into a "flap".:) I'm sure they will. I've seen...
Forum: Fabrication & Customization 01-15-2010
Replies: 14
Views: 6,100
Posted By B7510
Re: Snow blower mod

You ROCK THE ORANGE.
Forum: Service, Repair & Maintenance 12-30-2009
Replies: 47
Views: 17,618
Posted By B7510
Re: Drilled Hole into Engine Block

Many, many valid points.....and truly a difficult decision.....
Besides the low but constant 15 psi of the water pressure on one side of the repair there may be a constant much higher pressure (oil...
Forum: Service, Repair & Maintenance 12-21-2009
Replies: 21
Views: 4,388
Posted By B7510
Re: How can I loose stubborn nuts?

Hi Joe
I always try to set up a vibration so that the penetrating fluid is able to penetrate as much as possible to aid the loosening process. Most often I use an air hammer with a round blunt...
Forum: Service, Repair & Maintenance 08-18-2009
Replies: 12
Views: 5,469
Posted By B7510
Re: B7100 cooling system info

I believe the 0.9 represents bar 1 bar = 1 atmosphere of pressure, about 14 psi. 0.9 is 13.5 psi.

Here is a link to an online converter. Just plug in 0.9 and select bar then convert to pounds...
Forum: Service, Repair & Maintenance 07-02-2009
Replies: 31
Views: 7,593
Posted By B7510
Smile Re: Dextron? in my kubota

Gee guys this is my first post and I don't want to sound picky but.....

Drop the "T" in Dex"T"ron and add UDT.

Hope you see the humour!!!!!:)
Showing results 1 to 17 of 17

 
Forum Jump

All times are GMT -8. The time now is 04:14 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.