Recent content by NS kubota

  1. N

    Kubota lmx3174/K74-24-09 snowblower

    Does anyone have any experience with the Kubota LMX3174 snowblower or know anything about the ne for this year K74-24-09 snowblower from Kubota. These unit look about 100 lbs heavier than most 72-74” blowers I have seen and researched. Any help or info would be great. Thanks in advance.
  2. N

    I hate my new L3901

    My question to you is do you keep your RPM's up most of the time ie 1800 or so if you idle the tractor a lot it will regen more often we had a L3901 and loved it other than it became too small for are work in 104 hours only regened 3 or 4 times. We ran ours at 1800 most always just a thought...
  3. N

    Kubota MX 4800 engine codes

    Thanks lugbolt I will idle up the tractor to charge better and see if the codes go away.
  4. N

    Kubota MX 4800 engine codes

    Has anyone had the codes come up on a Mx4800, Po606,po627 & po629? Codes just came up today while tractor was running at idle, not sure if that had anything to do with the codes. Thanks in advance.
  5. N

    MX 4800 4wd in high gear

    Thanks guys for the response, we got it figured out and I agree high gear is for road travel (we only plow in low) Dad was travelling from my house to his house and wanted to try the tractor in high 4wd which is still not a great idea a lot of internal gear moving too fast for something to go...
  6. N

    MX 4800 4wd in high gear

    We were out last night clearing snow with our new Mx4800 hst and tried to go in high range while in 4wd and the tractor would not move lots of noise but that was it. This doesn't make any sense to me but maybe that's how it works although our L3901 would work in 4wd in any range. Anyone else...
  7. N

    L3901 safety switches

    Timber lake 580, we had the same tractor until trading this Aug for a Mx4800 and the only switch that gave us trouble was the seat safety switch when I lifted slightly off the seat which wearing the seatbelt cured. When you said the tractor would not start butafter sitting for a bit it started...
  8. N

    Hydraulic hose size for snow blade

    Thanks again tooljunkie good to get some feedback from someone that has experience trying to route hoses etc. Also good to hear from a fellow Canadian.
  9. N

    Hydraulic hose size for snow blade

    Thanks guys I had another look at the tractor & loader and 1/4" will work better, thanks again and happy tractoring Sent from my iPhone using Tapatalk
  10. N

    Hydraulic hose size for snow blade

    Thanks Tooljunkie I will likely go with 3/8 just in case I decide to hook up something else down the road. Cheers
  11. N

    Hydraulic hose size for snow blade

    Just trying to figure out what size hydraulic hose I need to run our hydraulic power angle plow blade we are hooking up on the FEL. The hydraulic lines on the loader look to be 3/8" which should supply enough flow for the 2 cylinders. We are going to run 2 new lines from the rear remotes to...
  12. N

    Checking hydraulic fluid in MX4800

    Can someone tell me where the hydraulic dipstick is on a MX 4800 tractor the L3901 we had, the hydraulic dip stick was around the floor board area but I don't see it on this unit. I want to hook up my hydraulic hoses for my plow blade which are dry and will need to add fluid and don't want to...
  13. N

    Tire chain newbie

    These chains should be fine, the width is the only difference less than 2 inches wider and the height is the same. Most chains will fit several different size tires. where in Canada are you located? We have a set of the Trygg smt flexi chains from our L3901 tire size is 15-19.5 that should...
  14. N

    Rear wheel spacers and ice chains

    I have for sale 2rear wheel spacers complete with studs washers and nuts and a set of tregg studded ice chains. Chains will fit industrial tire 15-19.5 or similar. I have the pieces of chain to go with to make chains longer for bigger tires. The spaces and chains were on a Kubota L3901...
  15. N

    pricing question

    Free2fish that is a nice tractor and implements don't sell it too cheap they are hard to find in this condition. If I lived closer to you I would snap it up without hesitation. Take care