Recent content by lunasdude

I think the dealers are playing dumb or outright denying any recalls exist. In the case of my dealer, he played dumb, said no recall that he knows of? Also because of parts availability, they are hard to come by. The solution in this thread is perfect. They go on in a few seconds and come of...

I know this is a very old thread but hopefully this message will get back to everyone here. Thank you, thank you, thank you, A thousand thank-yous! Because of the information here I was able to get rid of the 1 bane of my existence, the Kubota quick connect. I tried everything including rocking...

Thanks, I was actually hoping there was a suspension kit that would retro fit my current kubota seat with arm rests. $847 for a seat without arm rest is IMHO a lot of money. Just me of course but Damm!

Is there an aftermarket air suspension I can use with my BX1880 seat?

I admit I did not go thru all 86 pages but what I did see from one particular side was very much anger, hatred and vitriol of the opposite opinion. As an independent, I see both sides as badly flawed but I do try to see the good in both, but I must confess it’s getting harder and harder as time...

Ahh, my friend, you have run up against what I call the "I need a bigger tractor conundrum" I have a BX 1880 and I have run up against this limit many, many times. I have done the boosting kit on the Hydro pressure slightly to increase lift capacity and even with that I frequently bump up...

When I got by little BX 1880 a few years ago, I thought the fuel gauge was broken! I started off draggin our yard for weeds with a drag harrow, then latter using a land plane (land leveler) and finally moving some dirt and gravel. Sat on the seat and literally tapped on the gauge,\hmmm...

WOW, just, WOW.:eek: I never thought I would run across this type of pure unadulterated anger & vitriol on this forum. But, here it is, and well I guess I will dump in my 26 1/2 cent opinion here. I am a registered independent in a Southwestern state that is just now starting to relax some...

I’ll be dammed!:eek: One of these bulbs is 1/4 in longer than the other one! I always figured they would be somewhat standardized?:confused: My bulb looks like the bigger one. So if you housing is like mine, then you should have room for either bulb.

Your very welcome! As long as the led lights are of the blade type and they fit in the socket, then there is room for bigger bulb in the housing. Hope this helps!

Just to be clear, The 194 bulbs go in the two red tail lights built in to the fenders. If you are talking about the amber (Orange) mouse ear side blinking lights they are the bigger bulbs. I Did not have a part number from the old bulbs. These were the ones I ordered after I recognized the size...

Well, it was a tow bar thing that comes with and screws in to most new car bumpers as there all dam plastic and styrofoam now, so i was hoping that it would suffice.:confused: The miata was lowered :rolleyes: to a few inches off the ground so there was no way for me to squeeze my fatt a@@ under...

Inertia my friend, inertia! My 30" flail mower can be felt but nothing to dramatic, the 48" dual bladed rotary mower feels (and sounds )like it's going to rip the back of the tractor off!:eek: Makes me pee a little every time!:D

Nooo. can't leave the phone at home! I have a little Bx1880 and what if I get attacked my a pack of coyotes or, or, a swarm of scorpions, or fall into a pit of rattlesnakes?? Very common in the desert! If i have my phone I can say HEY GOOGLE CALL 911 FOR ME!, between the bites, stings and...

You are very welcome! And you do have a point about LED lights in general and there longevity and craptasic build quality of some of them.. I have tried them in cars and have always been a bit disappointed with the result. As far as my little BX beast, I guess because it's not mission critical...