Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
kubotasam's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
kubotasam
replied to the thread
RCK54-23BX PTO YOKE
.
You need to disassemble the assembly to find out what is wrong with the spring. It should not be sticking out like it is. If you can get...
May 17, 2022
kubotasam
replied to the thread
B6000 Battery Charging Problem
.
The dynamo produces AC current. It is changed to DC with a rectifier located under the dash. Your dynamo should produce approximately 30...
May 16, 2022
kubotasam
replied to the thread
Need some help identifying mower deck.
.
I have an operators manual if you need and info on the setup.
May 11, 2022
kubotasam
replied to the thread
Need some help identifying mower deck.
.
The parts in yellow bolt to the frame of the tractor. The parts in blue hang from the yellow and suspend the deck under the tractor...
May 11, 2022
kubotasam
replied to the thread
Turnbuckle for check chains l3901
.
The part you lost is called a "clevis". Should be available at most any hardware store. What you can purchase at a hardware or home...
May 10, 2022
kubotasam
replied to the thread
Older B6000 namely I think 73-77
.
Disconnect the 2 wires coming from the dynamo. If built like a B7100 their should be disconnects in the wires on the left side of the...
May 9, 2022
kubotasam
replied to the thread
Rear axle issue. B4200
.
Something has broken inside the axel case. The axel is held in with a snap ring inside that case. Hopefully maybe the snap ring just broke.
May 7, 2022
kubotasam
replied to the thread
b7100 dynamo
.
I remember reading that you need to remove the head to replace the dynamo in the WSM/
May 4, 2022
kubotasam
replied to the thread
New to me B7610
.
You can grind the ends of the cotters to shorten them so the do not butt together. Then they should clamp tight to the axle. I guess it...
Apr 27, 2022
kubotasam
replied to the thread
New to me B7610
.
The clamping parts are called "cotters" # 80 in the illustration. They can rust into the hub and be very difficult to remove even after...
Apr 26, 2022
kubotasam
replied to the thread
New to me B7610
.
The large nut you referenced is on a bolt that travels through 2 round blocks with beveled ends. It forms a clamp to pinch the axel so...
Apr 26, 2022
kubotasam
replied to the thread
B6100D hydraulic pump
.
I believe it is the one on the bottom of the pump. It will be the smaller diameter of the two pipes.
Apr 25, 2022
kubotasam
replied to the thread
What's the ultimate 3-point sand/salt spreader?
.
I would think that an electric actuator would be easier to make work than a hydraulic cylinder and also much less expensive. I do not...
Apr 15, 2022
kubotasam
replied to the thread
Early first service B2601
.
Messicks price
Apr 12, 2022
kubotasam
reacted to
Mowbizz's post
in the thread
Attachments for BX23S backhoe
with
Like
.
Good move on the UPS switch. fedex has screwed up deliveries all over the country and several of mine. UPS always comes up to my house...
Apr 3, 2022
Top
Bottom