Recent content by Jonny4523

  1. Jonny4523

    RTR2570 - Mechanic keeps saying it’s too big for my L4310

    I've replaced a lot of radiators in my time. I always just replace the thermostat at the same times given how cheap they are. In fact, I just had the radiator out of my L4310 in order to get the steering cylinder out and decided to just go ahead and replace the thermostat since I had everything...
  2. Jonny4523

    L 4310 PTO Problems

    Tractor is new to me. I’ve always used the clutch when shifting to different speeds or turning on the PTO. This certainly reinforces that decision. I’m estimating $3500 repair. With three young kids, two jobs, and a night class, I just don’t have the free time to do it myself.
  3. Jonny4523

    L 4310 PTO Problems

    I think I found the exact issue:
  4. Jonny4523

    L 4310 PTO Problems

    I know this is an old post, but I'm having the exact same issue that's described here. Your link is no longer working. Any chance you could point me to a new parts diagram with what you're referring to?
  5. Jonny4523

    Hazard Lights Troubleshooting

    You might double check. My electrical diagram agrees with my picture and shows the solid red wire coming straight from the battery with the RW wire coming from the switch.
  6. Jonny4523

    Hazard Lights Troubleshooting

    Actually, in that picture, the hazard is the second from the bottom on the left side. The bottom right wire is the constant +12V from the battery that supplies both the hazard and the ignition cutoff. I was able to jumper 12V from another fuse last night and my flashers were in full function...
  7. Jonny4523

    Hazard Lights Troubleshooting

    Ok, 3am update because I just couldn't leave it alone. Took another look at my WSM and saw that I should have 12V to the hazard lights straight from the battery. Pulled the fuse block and I was able to measure battery voltage to the back of the fuse block. So I know my wiring is good from the...
  8. Jonny4523

    Hazard Lights Troubleshooting

    Well, even if it is 2am, curiosity got the best of me and I went back out to the garage. I found 1 wire coming into the hazard unit (all red) that appeared to give me battery voltage to ground (ground here being the mounting screw that the hazard unit bolts to, which I believe serves as its body...
  9. Jonny4523

    Hazard Lights Troubleshooting

    I'm having trouble finding very many ground connections. The one that I've found is behind the fuse box. It looks to be in great condition. I've tested continuity from it to the hazard bulb bases and it was strong. I was hoping my WSM would show electrical ground locations, but I haven't had any...
  10. Jonny4523

    Hazard Lights Troubleshooting

    I pulled the plugs. No signs of corrosion. I blew them out and sprayed with some air mass flow cleaner to be safe. Fuse was good. That was my first check. My WSM is showing the hazard relays, hazard units, and turn signal relays all being seperate. I even found a picture in the cabin portion...
  11. Jonny4523

    Hazard Lights Troubleshooting

    I pealed back that cover tonight and disconnected all connections. I blew all the junk out of them and sprayed them down with CRC mass flow sensor cleaner. But they all looked to be in really good shape. No signs of corrosion. As far as the hazard illumination, it illuminatesd in both the...
  12. Jonny4523

    Hazard Lights Troubleshooting

    I have been looking and I can't find a ground location schematic. The only locations I've found so far are at the fuse box, the battery, and the hazard lights themselves (which I checked with giving them 12V from the tail lights and using their own ground).
  13. Jonny4523

    Hazard Lights Troubleshooting

    my serial number is 60661. I have already cleaned that area out. I think I had a short earlier in the area due to caked up mud. I’ll check again.
  14. Jonny4523

    Hazard Lights Troubleshooting

    I’m trying to get the hazard lights working on my L4310. The shop manual shows the hazard unit, hazard relay, and turn signal relays all being separate. But the parts manual only shows a hazard unit (which physically matches the tractor). I’ve already replaced the hazard unit and the hazard...