Recent content by btackett

  1. btackett

    Will a KUFD110 kubota plow fit a B7100 HST?

    Thanks for the info John. Luckily I will only use it once, maybe twice a year for snow removal.
  2. btackett

    Will a KUFD110 kubota plow fit a B7100 HST?

    Nice, I see it in the picture. I went and paid the guy for the plow and he had his B6000 there with a fel on it and I saw the cradle and it looks like yours. The only downside I see to it is that I would have to remove my entire mmm deck and the support bracket on it to install the plow.
  3. btackett

    Will a KUFD110 kubota plow fit a B7100 HST?

    Thanks for the info, does anyone have a picture of the subframe? I am not really worried about the hydraulics as I will use a small winch no more than I will use it.
  4. btackett

    Will a KUFD110 kubota plow fit a B7100 HST?

    I found one about 3 miles from my house and wanting to know if it will work with my B7100 HST model tractor? I don't see any hydraulics on it but I have a small winch I could use for up/down. thanks. Here is a CL link: http://knoxville.craigslist.org/grd/3523146462.html
  5. btackett

    Kubota D750 engine parts for sale (TN)

    I have a couple of parts of a D750 engine from a B7100 HST tractor. Shipping will be $12 each flat rate USPS. Please PM me with questions. I have a good original nippendenso starter $50 A good fan/dynamo $50 A good hydraulic pump $75
  6. btackett

    Need help finding tiller part

    Not as bad as I thought. Took the sleeve to my machine shop and $40 later , whalaa I thought about doing a slip on sleeve but they were $20 + shipping so this worked out ok.
  7. btackett

    Need help finding tiller part

    As you probably know from my previous post that my 36" tiller is an older one and I do not know the mfg of it but found that most Metric parts fit it. Well all the bearings and seals were replaced except the upper feed shaft. I now have it apart and found out why it was leaking. The seal has...
  8. btackett

    b7100 hst trans service

    Yes, when you loosen the large bolt head the bolt is actually the screen with threads on the end. You will have an O-ring on both flat sides in a groove of it that seals it. I bought new O-rings ( part numbers are on the prev link of the parts manual ) They are about $1 each from the dealer...
  9. btackett

    b7100 hst trans service

    You have a filter on top under the center cover and two screens on both sides of the tranny. There are 3 drain plugs under the tranny, one on the mid PTO and one on each side of the rear axle final drives. Mine were painted orange. You will need a 26 mm socket/wrench to remove the two screen...
  10. btackett

    Replaced tines,seals and bearing on Tiller

    It has been guessed at a Befco, Coroni, Maletti but really not for sure. All the seals,bearings and bolts on it are metric so I assume it was made in Italy with 95% of other tillers. Every part has been available with a little research for it luckily but not makers markings on it anywhere.
  11. btackett

    Replaced tines,seals and bearing on Tiller

    Finally done! I replaced all the tines, seals, bearings and a new chain so it should be good for another 30 years. Never found out what make this tiller is. The replacement tines are 3/4" longer than original and 1/8" thicker. I got them at tillerblades.com for $3 each! What a deal. Just...
  12. btackett

    Chain adjustment on 3 pt tiller

    Found the chain and master link at TSC actually about $40 for everything. Then made a phone call to a friend about a local heavy machinery fab shop here in town and went to see the guy and he had a 5 ft piece that he gave me! I took my gear and he matched it all and said good luck.
  13. btackett

    Chain adjustment on 3 pt tiller

    After looking at the chain closer it has stamped on the links GERMANY with a sproket in the middle and 60 stamped under the sproket. Is this a type 60 chain and can you get replacements? The chain does not have a master link. Help :confused:
  14. btackett

    Chain adjustment on 3 pt tiller

    What is the recommended chain slack before taking out links for proper tension? Mine is kinda stretched and while I have it apart burning old tine bolts off I want to adjust the chain drive. Also , will this chain breaker work? Are any of the pins removable or are they marked...
  15. btackett

    Tractor maintenance schedule form

    I searched and found a few different types of forms but just put a few together to suit my needs. I have attached a copy to view, if anyone wants the pdf PM me with your email and I will shoot it to you. It is on word so you can make changes.