What did you do to or on your Kubota today?

Cfrazer · Apr 5, 2019

Installed the sub soiler on the tractor and solved my drainage problem for awhile.

Sent from my iPhone using Tapatalk

RCW · Apr 6, 2019

Did some spring grading on the driveway. Had ripper shanks down for a couple passes.
More touch-up to do.

Ollie helped until he got cold....

Sent from my iPhone using Tapatalk

scratchypants · Apr 6, 2019

We'll be tearing down a section of our small, dilapidated barn, so took a couple of small steps in clearing it out: moved the grill from the barn and placed it on the deck; moved the cement mixer from the barn to behind the chicken coop.

JeepinMaxx · Apr 6, 2019

Added a BXpanded bucket edge...

fj40dave · Apr 7, 2019

Drilled 37 post holes 2' deep for a customer....first time using the post hole digger......worked pretty well. The coupling kept coming off the PTO for some reason....kind of a PITA. Only went thru two shear bolts.
I have a whole container of those now.

SidecarFlip · Apr 7, 2019

Changed the oil in both M's today. T6 in the 5-40 flavor. Filters too. Quick 7 gallons.

BXHoosier · Apr 7, 2019

Moved my 12ftx12ft yard barn with my truck to make way for a new 24ftx24ft pole barn being built soon hopefully. Then, I used the BX to remove the concrete slab that was under the barn. Luckily, it was poured between 4 trees so it was already broken into 3 pieces.

fruitcakesa · Apr 7, 2019

Fabbed up a bracket to hold the rear remote hose ends.
No more loose, dangling hoses.

SmallChange · Apr 7, 2019

Moved about a cord of matted wet leaves out of the parking area with a landscape rake, and then dozed them over an embankment.

Moved about another cord of same out of the corner of our fenced area and pushed them into a pile of branches, compost, clippings, and previous years' leaves.

And hosed it down for the first time this year, having connected the outdoor water this morning. Let it dry in the breeze a while, put it into the barn (where I had just cleaned up a season's worth of neglect), and then sprayed a lot of the exposed and complicated metal with WD40.

ItBmine · Apr 7, 2019

Took my snowblower off, washed it and sprayed it with Krown to prevent any rust. Then gave the driveway a quick grading to fix all the gouges I made cutting the ice pack off with the loader when it first started to melt.

JeepinMaxx · Apr 7, 2019

dug my snowblower out of the shed (it's been there since I bought the tractor last year)

Put the blower, quick hitch, and PTO shafts on a pallet for the next potential owner

Orange4X4 · Apr 8, 2019

Replaced zirc fitting on rear of upper loader arm, cleaned and regreased
loader and found seal ring on bucket ram cracked & falling off.
Getting ready to change engine oil , filter & fuel filter.
Tomorrow go over brush mower clean & check for summer.

Lennyzx11 · Apr 8, 2019

Worked on my new cab but afraid it’s going to get hung up in the Woods!

Sent from my iPhone using Tapatalk

js5020 · Apr 9, 2019

Lennyzx11 said:
Worked on my new cab but afraid it’s going to get hung up in the Woods!

Sent from my iPhone using Tapatalk

Just cut a bigger hole through the trees,, you'll be fine

dirtydeed · Apr 9, 2019

Lennyzx11 said:
Worked on my new cab but afraid it’s going to get hung up in the Woods!

Sent from my iPhone using Tapatalk

To me, it looks like the beginnings of a new "stealth turtle" disguise. You'll be able to sneak up on anyone.

Chaentjens · Apr 9, 2019

JeepinMaxx said:
dug my snowblower out of the shed (it's been there since I bought the tractor last year)

Put the blower, quick hitch, and PTO shafts on a pallet for the next potential owner

[emoji6]

Sent from my SM-N950U using Tapatalk

LukyNumbrKevin · Apr 9, 2019

Ground is finally thawed so it is time to get some paths put it on the property, I made a video showing the process so far. This is part 1 of 2, more to come soon!

Video Link: https://youtu.be/6eNIiPLQk-8

mcgoo · Apr 9, 2019

ItBmine said:
Took my snowblower off, washed it and sprayed it with Krown to prevent any rust. Then gave the driveway a quick grading to fix all the gouges I made cutting the ice pack off with the loader when it first started to melt.

How did you oil spray it?

Sent from my SM-G955W using Tapatalk

GeoHorn · Apr 9, 2019

JS5020... took me a moment... but that is just TOO FUNNY!

I just HAD to plagiarize it and send it to one of my buddies... LOLOLOL

ItBmine · Apr 9, 2019

mcgoo said:
How did you oil spray it?

Sent from my SM-G955W using Tapatalk

Just with the spray can. I buy cans of it to use for a lubricant penetrating oil and rust preventative.

Then I bring my cars and trucks to the local Krown garage to have them sprayed.

What did you do to or on your Kubota today?

Member

Well-known member

New member

Member

Well-known member

Attachments

Banned

Well-known member

Well-known member

New member

Well-known member

Attachments

Member

Member

New member

Member

Well-known member

New member

New member

New member

Well-known member

Well-known member