B6100 front Pto shaft size issue 27mm x 22 vs. 18mm x 22 spline

I have a B6100 I need to attach a hydraulic pump to the front PTO which is connected to the crankshaft via a shaft/crank pulley adapter.

Looking for correct part number shaft/crank pulley adapter/electric PTO. These parts ARE supposed to be available from Kubota as I am told but no one can answer the shaft size question so far.

I have this B9310 complete assembly
70090-00104; CLUTCH ASSY
66704-88530 1 FLANGE, PTO ( Front PTO)
66704-88540 1 SHAFT, PTO (Front PTO) Is where my problem is

Just bought and received a 9310 shaft assembly for my 6100 off ebay. It looks like the B9310 I purchased has a larger spline diameter than my crankshaft is. This unit I bought has the complete hub assembly bearing, the electric clutch and a 27 mm by 22 spline shaft sleeve. My 6100 needed a 18 mm instead of the 27 mm.

Wish I had the micrometer earlier. But maybe one of you has a need for 27mm x 22 spline when I find the right answer

Anybody know what the 27 mm fits? IS the 66704-88540 1 SHAFT, PTO (Front PTO) the smaller 18mm size? Help appreciated OTT

Vic, It still appears to be 22 spline. Morton had some info I looked at on the "b7100 pto impossible to find" link and this question is for the 6100 tractor. Live wire from TBN and I made all the connections and measurements between out tractors and found the 27 mm fits a Kubota B7100 and the 18 mm fits the B6100. He now has the Shaft for the B7100 that he has been searching for - for a couple years. Are these sites not great to help get the right parts found and meet the right people?

smokinhart said:

I have a B6100 I need to attach a hydraulic pump to the front PTO which is connected to the crankshaft via a shaft/crank pulley adapter.

Looking for correct part number shaft/crank pulley adapter/electric PTO. These parts ARE supposed to be available from Kubota as I am told but no one can answer the shaft size question so far.

I have this B9310 complete assembly
70090-00104; CLUTCH ASSY
66704-88530 1 FLANGE, PTO ( Front PTO)
66704-88540 1 SHAFT, PTO (Front PTO) Is where my problem is

Just bought and received a 9310 shaft assembly for my 6100 off ebay. It looks like the B9310 I purchased has a larger spline diameter than my crankshaft is. This unit I bought has the complete hub assembly bearing, the electric clutch and a 27 mm by 22 spline shaft sleeve. My 6100 needed a 18 mm instead of the 27 mm.

Wish I had the micrometer earlier. But maybe one of you has a need for 27mm x 22 spline when I find the right answer

Anybody know what the 27 mm fits? IS the 66704-88540 1 SHAFT, PTO (Front PTO) the smaller 18mm size? Help appreciated OTT

Click to expand...

Live wire from TBN and I made all the connections and measurements between out tractors and found the 27 mm fits a Kubota B7100 and the 18 mm fits the B6100. He now has the Shaft for the B7100 that he has been searching for - for a couple years. Are these sites not great to help get the right parts found and meet the right people?

Smokinhart here. I see there are references to what I was doing for a front hub on the 6100 again and I thought I'd post my solution. I used an Ecoloc compression hub and a 26 mm collar to lock it on. Had my machinist design a hub shaft to extend the shaft through to the drive hub up front. Maybe a little confusing with that run together but check out this site and head out from there.
http://www.globalspec.com/SpecSearch/PartSpecs?partId={AF3709BF-908E-483D-B3B6-0001D21E1979}&vid=96328&comp=1959&qid=19577688

Ecoloc -- RfN 7110 18 x 26

Larger Low profile unit fits into hubs with smaller outside diameter and no axial displacement.

See More Product Information: Supplier's Website PDF
Specifications
Application Internal (Thru Bore)
Design Units Metric
Internal Devices
Shaft Diameter. 18.01 mm
Hub Diameter 1.02 inch
Clamping Length 0.7090 inch
Overall Length 1.73 inch
Specifications
Maximum Torque 131 Ft-lbs
Clamping Force Locking Device Generated