Post your ROPS light mounting pics

OC455

Member

Equipment
BX2350 LED ROP, FEL, Belly mower,modified snow blower, pole boom, middle plow
Sep 30, 2016
161
12
18
Rome NY USA
14650186_1148705361832565_7623103739808581527_n.jpg

14563556_1148705391832562_1066824535631204106_n.jpg

Hopefully these will turn out well. I used stake bed pockets that measured 3x1.5 inches and used flat stock to mount across the top of the stake bed pockets to the ROPS. I painted the pockets and top brackets the ROPS grey. The LED light bars are 12inch 72watts. The lights are IP68 rated so they're good to go for weather up this way.

I used a wiring harness that has a remote key fob to turn on the lights. Just need to run the wires and make them look nice and tidy before getting into anymore working with it.

When I was checking out how to power it from the rear, there was only two wires instead of three....one black ground, and one red with black stripe. I guess the newer BX's have the 3rd wire.

All and all, I think it turned out pretty good as far as a solid mount setup and the wiring was pretty simple.
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,283
3,868
113
Chenango County, NY
I used stake bed pockets that measured 3x1.5 inches and used flat stock to mount across the top of the stake bed pockets to the ROPS.
I looked at stake pockets, too. Maybe try them for a different mounting location, but this one works, except it should have been on the left side.

I'm left handed, and tend to look over my right should when backing up. The location I used tends to be in my eyes when going in reverse.:eek:
 

Attachments

Last edited:

OC455

Member

Equipment
BX2350 LED ROP, FEL, Belly mower,modified snow blower, pole boom, middle plow
Sep 30, 2016
161
12
18
Rome NY USA
I put mine up high just so the light will be over my head and won't have to worry about my big noggin getting in the way.....and mounted the rear facing light lower to keep enough light shining down towards the back of the tractor.
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,283
3,868
113
Chenango County, NY
Well, decided to try a high mount. Nothing fancy; just angle brackets.



Sent from my iPhone using Tapatalk
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,283
3,868
113
Chenango County, NY
Came out pretty good. They clear my noggin so far.
Realized my switch got broken over the summer. [emoji31]



Sent from my iPhone using Tapatalk
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,283
3,868
113
Chenango County, NY
Figure if I ever put light bars on it, just move brackets to fit![emoji106]


Sent from my iPhone using Tapatalk
 

OC455

Member

Equipment
BX2350 LED ROP, FEL, Belly mower,modified snow blower, pole boom, middle plow
Sep 30, 2016
161
12
18
Rome NY USA
Figure if I ever put light bars on it, just move brackets to fit![emoji106]


Sent from my iPhone using Tapatalk
Looks good so far!!! I managed to destroy my damn amber rotator light....I snapped the damn thing right off. The magnetic mount held fast...the rest of it ended up under my mower deck....while it was on....no more safety light....UGH
 

OC455

Member

Equipment
BX2350 LED ROP, FEL, Belly mower,modified snow blower, pole boom, middle plow
Sep 30, 2016
161
12
18
Rome NY USA
I found amber light bar covers that are 6 inches in length. Ordered 4 of them and they snap into place over the light bars....they sort of overlap in the middle. There's the on/off button and the second button is a flash mode with 5 different flash patterns. Hopefully I can get a video posted here of how it looks.

So if I am not using the light bars for illumination I can snap the covers over them and use them as safety lights.

Still PO'd about breaking my rotator light.
 

08quadram

Member

Equipment
bx2350d; Taylor Way 48" tiller; Farm King 50" snow blower
Apr 28, 2014
289
1
18
strawberry point, ia
Came out pretty good. They clear my noggin so far.
Realized my switch got broken over the summer. [emoji31]



Sent from my iPhone using Tapatalk
Watch your head. I would probably bust my head on the bottom of the brackets. Well probably long before that, I'd lose them from a tree.

I like the height. You won't be getting blinded by them as I can with mine.

Mike
 

KeithG

Member

Equipment
2000 Kubota B2710, Woods BH75 backhoe, LandPride York Rake, B2783 Snow Blower
Jan 1, 2016
129
5
18
Rindge, NH
Just realized I never put up pictures of my ROPS lights. I installed a canopy and updated my lights after installing it. Here are the pictures...
 

Attachments

BAP

Well-known member
Lifetime Member

Equipment
2012 Kubota 2920, 60MMM, FEL, BH65 48" Bush Hog, 60"Backblade, B2782B Snowblower
Dec 31, 2012
2,513
657
113
New Hampshire
So that's what the big glow in the sky was to the south of me. They look great.
 

KeithG

Member

Equipment
2000 Kubota B2710, Woods BH75 backhoe, LandPride York Rake, B2783 Snow Blower
Jan 1, 2016
129
5
18
Rindge, NH
So that's what the big glow in the sky was to the south of me. They look great.
LOL! Thanks. Going to be using them for the first time this winter with my snowblower. :D
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,283
3,868
113
Chenango County, NY
Watch your head. I would probably bust my head on the bottom of the brackets. Well probably long before that, I'd lose them from a tree.

I like the height. You won't be getting blinded by them as I can with mine.

Mike
Mike and OC455 - I've run the tractor several times since posting the pictures at #44 and 45.

Your BX2350's have the same ROPS as my BX2360?

Thus far - no hitting my head. I'm 6'4" and 240 or so, if that helps.

At first, kinda pissed the brackets bent in when tightening, but think that may help ease sharp edges. I also rounded the corners on a grinder some.

The lowest part of the bracket could be cut off, but wanted to keep the extra holes for other lights, if needed!

Haven't used at night yet. We'll see, so to speak!:p
 
Last edited:

grandall4

New member
Aug 27, 2015
7
0
0
Granby MA
Temporary mounts using trailer stake pockets and flat stock. The stake pockets have small rib that needs to be ground down to allow the light to mount squarely.


 

lordulrich

New member

Equipment
BX 2370, 60 MMM, Loader, Front Mount Snow Blower, Landpride 3 pt blade, Tiller
Jul 28, 2016
82
0
0
SE Minnesota
Just finished today dressing up my BX, wanted to get them on before the snow flies. The lower lights (just below the ROPS pivot point) on the front are aimed out where the blower will throw snow, and the rear are pointed at the 3 point. I put it away before the dark, but it sure lit up the shed.
 

Attachments

MattN03

Active member

Equipment
2011 B3200, LA504 FEL w/B2366 SSQA conversion, BH76 BH, EA Wicked 55
Sep 5, 2016
222
40
28
KY
Got mine wired and got to try them out tonight. A 22" spot/flood combo up front. In the rear, I have 2 flood/spot cubes.
 

Attachments