Search results

I am looking for a hood for a L295DT. Check your barns......

Finally fixed my hydraulic problems and just want to thank everyone for your help and information. After replacingthe pump and going through all of the hyd cylinder, replaced the control valve with a used one from Wenger's. Good place to find hard to find parts. Now it is on to the body work...

A welder is a good investment when owning and working on tractors. I have a L295DT and have had to top off of mine and it went back with no problems. Good luck

If you have a welder, tack a piece of flat stock or a 3 inch bolt to the plug to give you some leverage to remove it.

Hey OTT, Need some hydraulic help on my L295DT. Just put a hyd pump on this ole girl after removing and cleaning the control valve and all of the hydraulic parts under the seat. Even replaced the piston and cylinder due to some rust. Changed all of the fluids and filter. I have a block on my...

Looking for a complete seat assy for L295. Not sure if other tractors have same assy, any help is appreciated.

MDsteve, I also have a L295DT with a 1200 loader. Could you send me some pix of how your hyd hoses are connected. Email to sales@stepdoctor.com Thanks, George

MDsteve, I cant answer your question, but I have an L295DT with a 1200 loader and have a question for you about your hydraulic connections for the loader. I have the same block attached to the relief valve but have a bad hyd pump that I am going to replace. Do you have a 3rd hose from your...

I may have what you need. Email me at sales@stepdoctor.com and I will send you the info I have. The file is too big to send via OTT

Found trouble with 4wd. Rusted snap ring on slip collar on drive shaft. Easy fix, just had to take time to fix it. Thanks for your help

Scott, I have some info I think you can use sent to me by another OTT member. I will try to attach it to this reply. If it does not work, send me a private meassage or email me at sales@stepdoctor.com It did not work, file is too big.

Vic, I tried what you said to do and removed the bypass hose and plugged the ports. The lift arms do not move when the hose is removed and the block is plugged. This block takes the place of Part no. 35300-36720 which has a channel for the pressurized fluid to pass through into the relief...

Still working on my L295DT trying to resolve an issue with hydarulics. Dissmantled the hydraulics and found water damage in cylinder, replaced cylider and piston, also found a stuck unloading valve and dirty check valve. Cleaned everthing and reassembled and now the 3 pt raises very, very...

Vic I will send you an email with picture of the block I am talking about.

Vic, I do have a 1200hd loader and a l720 backhoe on this tractor and both are plumbed from the pto pump. My problem with that is I do not have a 2 stage clutch and loose loader functions when I depress the clutch. I checked the pressure on the block attached to the relief valve. I will check...

Vic, there is a block attached to the top of the relief valve that took the place of the factory cover for the relief valve. I assume this could be used to feed a fel. I am using a pressure gauge from Northern Hydraulic that reads up to 3000psi. I am connecting to the forward fitting on the...

Hey guys, I need some info on hydraulics. Trying to troubleshoot my system on an L295DT. Need to know the basics. How the fluid flows through the entire system etc. Pump to relief valve to control valve to hyd cylinder to draft control and back to pump is what I think happens, but no sure...

Scott, I have a l295dt also and have found Messick's (www.messicks.com) is a good place to get parts. They have a page where you can request downloads for each part of the tractor. Also, www.tractorsmart.com is a good place too. They are very helpful. Good luck, George

Does anyone know if there is a common problem or weak areas in the 4wd of an L295dt. The lever works, the drive shaft moves but front wheels do not engage. Also can the front diff/axle be removed without removing the radiator etc. It looks like there is enough room to move the diff forward...

Magkarl, thank you and I would appreciate it if you would shoot me an email with the 1200 info. I have looked everywhere for some info with no luck. Please send it to sales@stepdoctor.com Thank you