Search results

  1. A

    Beauty of frozen image blowing snow

    Wife took a shot of me cleaning up after the weekend snow dump. It was fascinating to see the capture of the segments of snow as thrown out by each impeller blade . . . and being able to see the segmentation in the discharge 10-15 yds away
  2. A

    Experience with PTO Clutch failure BX2350?

    Was chipping 3 1/2" poplar branches yesterday when it started bouncing in and out of the teeth and then pto shaft stopped turning. No strange noises that I heard. No grinding. Cleaned chipper out and tried again but shaft barely turned. Checked mid pto via attached front mount snow blower -...
  3. A

    Forklift attachment for my BX 2350

    42" forks made from 4"x 2"x 1/2" rectangular tubing Adjustable width No quick disconnect - just copied bucket attachment points Appears to be able to handle all my little hippo can give them
  4. A

    The "Rare" RT110

    Not many of these around:)
  5. A

    Added Rear Hydraulics to BX2350v

    Decided to tap off the front valve body to give me rear hydraulics (used the forward/backward lever movements circuit). It all ended up tucking away quit nicely. Only issue I ran into was when the Hydraulics Direct nipples failed (started working as check valves) so I had to buy pieces from...
  6. A

    Modified my Bagger GCK60-23BX for Quick Hitch

    Wanted something to pickup leaves but needed something that could be changed in minutes. So I bought a used GCK60-23BX and did the following conversion. First I needed to make an adapter between the existing bagger structure and my quick hitch. That defined the driveline mods I needed to make.
  7. A

    Front Mount Fertilizer Spreader

    I like to see where I'm throwing fertilizer so I bought a "quad spreader" and mounted on the front of my Kubota. Takes about 3 mins to mount/remove
  8. A

    Headlight issues - try cleaning dirty switch

    Two seasons ago, my headlight operation on my BX2350 was sporadic. I removed the switch, opened it up and found it packed up with dust and grass. Cleaned it, reinstalled and its still working great.
  9. A

    Used drive shaft for BX1850 to front quick hitch

    Drive shaft (p/n 7006002752?) for a BX1850 to the front quick hitch. Yoke centerline to centerline is 35". Asking $200 (new shaft for my BX2350 was $500). Note: I did advertise this back in 2011 and forgot about it when life got busy ... sorry
  10. A

    For Sale: Boot Kit for Kubota 60" mower BX2670

    I purchased a used bagger which had been matched with a BX2670 tractor and mower. I run a BX2350 with a 54" mower so I needed to buy a different (new) boot kit. ($300 plus). Includes approx 3ft of tube to connect to blower inlet. $75
  11. A

    For Sale: CV Joint for Kubota GCK60-23BX Bagger

    Modified my bagger to work with quick disconnect hitch. Needed longer PTO so stock CV joint not required. Input is 1 3/8" 6 spline (tractor pto), output is 25mm dia hole. Tractor end pto lock pin missing. $50
  12. A

    Used drive shaft for BX1850 to front quick hitch

    Drive shaft (p/n 7006002752?) for a BX1850 to the front quick hitch. Yoke centerline to centerline is 35". Asking $250 which is 50% what I paid for new shaft for my BX2350. Calgary Alberta
  13. A

    Why is my mid PTO drive shaft to short?

    My tractor is a BX2350D. I bought a used BX2750C snow blower with a BX2751* quick hitch. This setup supposedly had been on a BX1850 tractor. The Quick hitch mounts up perfectly to the tractor, the blower mounts on the quick hitch and blower pto shaft connects to the 14 1/2" long quick hitch...
Top Bottom