Search results

I have a 2010 B3030 HSTDCC that I purchased used with 42 hours on it in the fall 2010 Kubota bought it back from original purchaser due to a clunk when ever it changed direction They install a new coupler from engine to hydrostatic unit,new hydrostatic unit,new rear diff,1 new rear axle & a...

Here is one I built 3 years ago 64" wide /18 " tall / 16 " wings On my B3030 everything was to small or to big "of the shelf" & way over my budget Lucky for me have a very good steel fabrication shop 5 minutes from work & they supplied & bent up all the steel for under $300 tax in (1 4x8 sheet...

I have a B3030 & run mine of my 3rd function which leaves my 2 rear remotes free & no long lines from back to front to get snagged on As for size mine is 66 inch & I built it so you have same chassis just less horse power so stay 60 " ish & it should do you well & not beat loader up As for 3rd...

A bit more info to add to this I picked up all my piece's @ Princess Auto except for the hoses had them made @ a local small engine/hydraulic hose shop Valve is a Bosch RexRoth with #6 ORF fittings Sent from my SM-A520W using Tapatalk

I have a B3030 & have a 84 inch LandPride rake it's about all I want in heavy going. But you could purchase it & loop 6 inchs off each end Sent from my SM-A520W using Tapatalk

I made a bit of a ohmision The 2 lines from C1 - C2 got to the original hoses you removed from original valve bank not back to valve (tried wrighting reply before my second cup of coffee) Paul Sent from my SM-A520W using Tapatalk

Ok This is the most common set up You take the 2 lines from your loader control off that valve bank & take them to new valve porrs P1 & P2 Next you take 2 lines from you new valve on ports C1 & C2 back to your loader bank Next you run new hoses from your new valve to where ever you want new...

As soon as I'm near my tractor I'll get som pictures & a more detailed how I got mine hooked Paul Sent from my SM-A520W using Tapatalk

This is a drawing of the valve & plumbing Cost affective & works for my grapple & hydraulic salt spreeder Made my own brackets Valve,hoses & disconnects was just under $500 Canadian Sent from my SM-A520W using Tapatalk

You could put a mechanical/electric 3rd function on front & "borrow " the hydraulic pressure from the curl/dump on front loader simple plumbing, only down fall is you can use 3rd function or curl/dump not both @ the same time How ever very convenient that with the flip of a switch you can go...

There is all so a service bulletin about the motor being to tight to chute needing to be adjusted away to give more clearance & not jamming up Mine wouldn't turn 1 way & had to follow the Kubota servicing bulletin & remove motor slot out 2 of the 3 mounts & put back together Hasn't been an...

Turbo MS in Quebec Wonderful group do turbocharger repair/rebuild in house Excellant service I have used them over 10 years & not one issue Frederic has been very helpful on many older & newer turbo's They have a wed site Paul Sent from my SM-A520W using Tapatalk

Do you have an old(I mean old)headlight capsule say a 6014 or a 6054(big round or big square) only one side has to light(voltage & amp load) Now what ever side of light work(a positive & a negative) put 2 wires on it(there are 3 terminals)test it across a good battery does it light(yes or no)...

What pressures do you have hi/low? What is your temp drop from upper outlet to lower inlet @ condenser rad(as close to where pipes end before they go into the tubes? Are your sure it's properly charged? Just because pipes appear small doen't mean there under size a lot of these systems are...

I have a 2010 B3030 with cab & got lucky & stumbled across a early 2003/4 John Deere 48 hoe that was REAL cheap due to a couple of repairable issues & needing to be modified to fit the factory subframe mounts for the Kubota backhoe.I'm lucky & can make anything I needed to get it to fit . So if...