Search results

Few years back had to get a new septic system for the house. Good old Louisiana clay about 6-7 yards which now looks like a jungle scene from Jurassic Park. Some small trash trees grew in it and I can cut these down and burn them. But still have to deal with the clay. At present the FEL is a...

Hi all, recently did the oil change on the engine of my L3800. Manual for the L3800 says to use 7.5 quarts including the oil filter which was changed out at the same time. Now for the confusing part. The manual shows a dipstick that has a square section at the end with two lines with cross...

I'd like to change out the 80-90 weight gear oil on the gearbox on my woods bush hog. Now after carefully reading the manual there are only two plugs on the gearbox. On top you have the vent plug and on one side you have the oil check plug. You remove the lower one to make sure the oil level is...

Tired to get the bush hog installed on my l3800 and excersize in futility. Had the right one on with no problems this is an adjustable arm. ok get the top link hooked up no problems. Left link is non adjustable and the section that has the hole for the link pin is about 2" higher than the right...

Went to check the liquid levels in my new (december 2013) L3800. Motor oil way above what it should be and almoost clear in color. Looked at the hst window on the side and cannot tell if it's high or low. Used a flashlight and still cannot tell the level. From some of the posts here I'm thinking...

Ok I have a L3800 with Fel. It also comes with a woods bushhog. Now if I disconnect the bushhog isn't there a bar that goes through the holes in the lift arms and secured with 4 pins?. My reasoning about the bar is that it is required there to keep the lift arms from rubbing against the tires...

My 12 year and 11 day old hot water heater decided to take a dump last night. Managed to get a new one at lowes and it's now in place of the old one. At one point in time I gave serious consideration to using my L3800 and about 200' of 3/4" nylon rope to get it out the back door. Last experience...

Can't afford the $$$ for a grabber and it's installation for my L3800. Was considering getting a set of forks from Northern tool at around $370 or so. Anyone use forks to pick up tree branches and stuff around their property?. That is basically what I want them for. One pile is too close to some...

I remember late last year about some members here saying they can't wait to try out snow removal with their new tractors and fels. Guess the weather gods argreed with a lot of you as we have had the worst winter regarding snow in a long time. So got enough snow already?. So how did your snow...

Well this is interesting, just noticed John Deere ads on this forum. Frank

Looking to add a ballast box for my L3800 with fel. Anyone know what they go for??.zI have about 500 lbs roofing lead sheathing so could use that as the ballast.Also2 50lb lead ingots. Frank

Lookinh for a ballast box for a L3800 with a 524 fel. Tried to look on the kubota pages but for whatever reason could not get the specs or price. Want the one that works off the 3pt hitch. Thanks,Frank

Well we skated out this year for hurricanes. My old cart I actually bought with our first craftsman 16hp tractor. Three tractors later paint is shot and deck is starting to rust. Since I have a bigger tractor what is out there that will carry more than 22cu.ft?. That is about the largest...

Well took the L3800 I just bought and cut about 3.5 acres of grass. Dirty job but someone had to do it. Everything worked fine. Only problem I had was with the longer wheelbase. Every so often would loose traction on one of the rear wheels. My land that I cut isn't exactly level. 4 wheel drive...

Most tractor dealers rate their tractors something like this sub compact, compact. standard and go on from there. So having said that where would my L3800 with 38 or 39 horses fallin?.Frank

Didn't know where to stick this so if the mods wish to move it fine. As you probably know by now I just bought a new kubota L3800 and have a few cans around filled with diesel from the old JD 2305. That particular machine sits lower to the ground so it was no real problem to just pour the diesel...

I've read all the manuals for both the tractor (L3800) and for the bush hog but still have a problem. So here goes. At present the front end closest to the pto is almost touching the ground. Does one use the lift link positioning lever to get that end up when cutting grass?. Just got it and...

OK, don't flame the new guy. Just got my L3800 HSt with fel and woods bush hog. I'm selling my '06 2305 and if I remember right its a sub compact tractor. I did buy a frontier 4-5' rake to cleanup the front yard after storms. The manual says its a limited class one with class one pins. I checked...

I'll be getting my brand new Kubota L3800 with LA524 front end loader and woods bush hog hopefully this weekend. And soon to add a grappel to get rid of the piles of dead tree limbs and such. Finally had it with the local JD dealer. Must think his stuff is made from unobtainum as his prices...