Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
TwitchyMcJoe's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
TwitchyMcJoe
replied to the thread
L185DT Bent Bevel Gear Shaft
.
Yes, I did. Both bevel gear housings and the differential.
Apr 28, 2024
TwitchyMcJoe
replied to the thread
What did you do to or on your Kubota today?
.
I finally fixed my L185DT, and I immediately put it to work mowing about an acre just to be sure nothing went wrong with the repair. I...
Apr 28, 2024
TwitchyMcJoe
replied to the thread
L185DT Bent Bevel Gear Shaft
.
She lives. I found no oil in the other gear case or front differential. I will keep an eye out for leaks, buy no wonder the bearings failed
Apr 28, 2024
TwitchyMcJoe
replied to the thread
L185DT Bent Bevel Gear Shaft
.
Not needed. It's beat up, but serviceable. I had to angle grind some slots in the old bevel gear to pull it off with the puller...
Apr 26, 2024
TwitchyMcJoe
reacted to
007kubotaguy's post
in the thread
L185DT Bent Bevel Gear Shaft
with
Like
.
Great. Looks like my box survived the 3,000 mile ride. You should not need a puller to get the axle gear off. Just remove the snap ring...
Apr 24, 2024
TwitchyMcJoe
replied to the thread
L185DT Bent Bevel Gear Shaft
.
Yeah, it should, except that one of the loose ball bearings or, the other gears, put a few dents in the end of the shaft. Pulling the...
Apr 24, 2024
TwitchyMcJoe
replied to the thread
L185DT Bent Bevel Gear Shaft
.
Parts are here! I've got to get a gear puller, but it should bolt right on!
Apr 24, 2024
TwitchyMcJoe
reacted to
Trimley's post
in the thread
Custom Grading Blade Cutting Edge
with
Like
.
A blast from the past...built to last. Over the years I've seen several very similarly built. A good candidate for hydraulic angle.
Apr 18, 2024
TwitchyMcJoe
reacted to
old and tired's post
in the thread
Custom Grading Blade Cutting Edge
with
Like
.
I'd run it as is... it looks to have more than an inch of blade left before anything needs to be replaced. If you want, flip the blade...
Apr 18, 2024
TwitchyMcJoe
replied to the thread
Custom Grading Blade Cutting Edge
.
I can't find any more information online, so I'm not sure what else they made either. The other side of the blade is in good shape, so...
Apr 18, 2024
TwitchyMcJoe
replied to the thread
Custom Grading Blade Cutting Edge
.
Thanks. I'll check the spacing on it today. I did find a little more information on it from this brochure for sale on eBay. The blade on...
Apr 18, 2024
TwitchyMcJoe
reacted to
Motion's post
in the thread
Custom Grading Blade Cutting Edge
with
Like
.
Even though ancient, unless you have the facilities to fabricate and harden the steel, consider purchasing a new one. Most blades use...
Apr 18, 2024
TwitchyMcJoe
reacted to
Russell King's post
in the thread
How best to add 3pt hitch
with
Like
.
I would start with a trailer mover frame to get the geometry right. May be able to get one that has some removable receiver so it can...
Apr 17, 2024
TwitchyMcJoe
posted the thread
Custom Grading Blade Cutting Edge
in
Implements & Attachments
.
Hey everyone, I have acquired an ancient, 7 foot, Grove Manufacturing Company three point grading blade that was cheap for good reason...
Apr 17, 2024
TwitchyMcJoe
replied to the thread
FEL
.
Does the L295DT take the L1200 loader from other L series tractors of the same era? You might find an L175, L185, L245 etc. With a...
Apr 17, 2024
Top
Bottom